Skip to content

fix(rock5b): fix broken links in FAQ page (Q8) #1723

New issue

Have a question about this project? Sign up for a free GitHub account to open an issue and contact its maintainers and the community.

Sign up for GitHub

By clicking “Sign up for GitHub”, you agree to our terms of service and privacy statement. We’ll occasionally send you account related emails.

Already on GitHub? Sign in to your account

Merged
Milir-Radxa merged 1 commit into from
Apr 24, 2026
Merged

fix(rock5b): fix broken links in FAQ page (Q8) #1723

Show file tree
Hide file tree
Changes from all commits
Commits
Show all changes
1 commit
Select commit
File filter

Filter by extension

Filter by extension
Conversations
Failed to load comments.
Loading
Jump to
Jump to file
Failed to load files.
Loading
Diff view
Diff view
6 changes: 3 additions & 3 deletions docs/rock5/rock5b/faq.md
View file
Open in desktop
Original file line number Diff line number Diff line change
Expand Up @@ -52,14 +52,14 @@ ROCK 5B 支持将 USB PD 电源协商至更高的电压，如 9V、12V、15V、2

原因确认:

去掉 eMMC Module, MicroSD 及 NVME 设备，然后通过 USB 线连接板子和PC，此时看设备是否进入 [Maskrom 状态](./low-level-dev/maskrom/)，
去掉 eMMC Module, MicroSD 及 NVME 设备，然后通过 USB 线连接板子和PC，此时看设备是否进入 [Maskrom 状态](./low-level-dev/install-os/rkdevtool_maskrom)，
如果不是MaskRom状态，则大概率是下面的原因:

在 [通过 USB 烧录系统到eMMC](./low-level-dev/maskrom/) 的时候没有按照说明 按 Maskrom 按键，导致烧录系统到了 [SPI Flash](./low-level-dev/maskrom/erase)中, 而系统启动的时候，先读取SPI的信息，此时出现错误，无法正常启动。
在 [通过 USB 烧录系统到eMMC](./low-level-dev/install-os/rkdevtool_maskrom) 的时候没有按照说明 按 Maskrom 按键，导致烧录系统到了 [SPI Flash](./low-level-dev/install-os/rkdevtool_spi)中, 而系统启动的时候，先读取SPI的信息，此时出现错误，无法正常启动。

解决办法：

[清空 SPI Flash](./low-level-dev/maskrom/erase), 然后重新按步骤 [通过USB烧录系统到eMMC](./low-level-dev/maskrom/)
[清空 SPI Flash](./low-level-dev/install-os/rkdevtool_spi), 然后重新按步骤 [通过USB烧录系统到eMMC](./low-level-dev/install-os/rkdevtool_maskrom)

## Q9： Radxa APT 公钥不可用

Expand Down
6 changes: 3 additions & 3 deletions i18n/en/docusaurus-plugin-content-docs/current/rock5/rock5b/faq.md
View file
Open in desktop
Original file line number Diff line number Diff line change
Expand Up @@ -52,14 +52,14 @@ Follow the steps below to troubleshoot ROCK 5B:

Confirmation: Remove eMMC Module, MicroSD and NVME devices.

Remove the eMMC Module, MicroSD and NVME device, then connect the board and PC via USB cable, then see if the device enters [Maskrom state](./low-level-dev/maskrom/).
Remove the eMMC Module, MicroSD and NVME device, then connect the board and PC via USB cable, then see if the device enters [Maskrom state](./low-level-dev/install-os/rkdevtool_maskrom).
If it's not in MaskRom state, it's most likely due to the following reasons.

In [Burning system to eMMC via USB](./low-level-dev/maskrom/), did not follow the instructions to press the Maskrom button, causing the system to reach the [SPI Flash](./low-level-dev/maskrom/erase), and when the system starts, it reads the SPI information first, and then there is an error and it cannot start normally.
In [Burning system to eMMC via USB](./low-level-dev/install-os/rkdevtool_maskrom), did not follow the instructions to press the Maskrom button, causing the system to reach the [SPI Flash](./low-level-dev/install-os/rkdevtool_spi), and when the system starts, it reads the SPI information first, and then there is an error and it cannot start normally.

Solution:

[Empty SPI Flash](./low-level-dev/maskrom/erase), then follow the steps again [Burn system to eMMC via USB](./low-level-dev/maskrom/)
[Empty SPI Flash](./low-level-dev/install-os/rkdevtool_spi), then follow the steps again [Burn system to eMMC via USB](./low-level-dev/install-os/rkdevtool_maskrom)

## Q9: Radxa APT public key not available

Expand Down
Loading