Introduction to IOS-XR Ansible

NOTE: This IOS-XR Ansible only supports up to Ansible version 2.3.

In the nutshell, Ansible is an automation tool for configuring system, deploying software, and orchestrating services. Unlike Puppet and Chef which is an agent-based architecture, Ansible does not require daemon running or agent pre-installed on the target nodes to perform configuration tasks. Ansible could be specified to run either on local server or on remote node.

The different between local and remote connection mode in Ansible is basically where the script (so-called Ansible module) is being run. For the remote mode, Ansible automatically attempts to establish SSH connection to the remote node. Once established, it transfers the script and runs it on the remote node. The script responds to the server in JSON formatted text. This mode requires setting up third-party namespace (TPNNS) on the IOS-XR node.

As for the local mode, Ansible run the module script on the local server. The script has to establish a connection to the remote node itself. The local mode module uses Ansible network module to establish SSH connection to the IOS-XR console to run CLI command.

There are 6 different ways to access IOS-XR in local mode.

Console CLI - connect to IOS-XR console through SSH port 22 and use CLI commands.
TPNNS CLI - connect to IOS-XR Linux shell through SSH port 57722 and use helper programs, /pkg/bin/xr_cli or /pkg/sbin/config.
Raw XML - connect to IOS-XR console through SSH port 22 to exchange XML construct with IOS-XR xml agent.
Raw NETCONF 1.0 - connect to IOS-XR console through SSH port 22 to exchange NETCONF 1.0 XML construct with IOS-XR netconf agent.
Raw NETCONF 1.1 - connect to IOS-XR console through SSH port 830 to exchange NETCONF 1.1 XML construct with IOS-XR netconf-yang agent.
YDK NETCONF - use the Cisco YDK API service to manage IOS-XR device through SSH port 830.

Managing the IOS-XR device in the remote mode required TPNNS through SSH port 57722 with the helper programs, /pkg/bin/xr_cli and /pkg/sbin/config, to deliver CLI commands and configuration to the IOS-XR, respectively. This remote mode connection is identical to TPNNS CLI running in local mode except for how the SSH connection is being established and where the script is run.

Understand connection variants

With different variants for local and remote modes mentioned earlier, before implementing Ansible modules, one needs to be aware of their limitation.

Linux-based vs. QNX-based IOS-XR

QNX-based IOS-XR can only run in local mode
Earlier version of Linux-based IOS-XR also can only run in local mode due to incomplete Python libraries
Linux-based IOS-XR (eXR 6.0.2 or later) can run both remote and local modes

CLI vs. XML/NETCONF

With CLI mode, you can do all CLI commands as you would do interactively.
The XML/NETCONF mode allows you to use Cisco XML or NETCONF commands in XML construct to configure IOS-XR.

Console CLI vs. TPNNS CLI

Console CLI allows you to do all CLI commands as you would do interactively.
TPNNS CLI can either be implemented in local or remote mode. It connects to IOS-XR Linux shell and requires helper programs, /pkg/bin/xr_cli or /pkg/sbin/config, to deliver CLI commands or configure IOS-XR, respectively. Currently, "commit replace" is not supported by /pkg/sbin/config.

Raw XML/NETCONF vs. YDK NETCONF

Raw NETCONF mode allows you to configure IOS-XR using NETCONF commands in RPC XML construct through standard SSH port 22 with termination sequence ]]>]]> and port 830 with ## termination sequence. The response is also in RPC XML construct.
Alternatively, you can use YDK python API to configure IOS-XR through SSH port 830. The API automatically generates the RPC XML construct based on the YANG model provided.

NOTE: IOS-XR NETCONF 1.1 XML construct is based on Cisco IOS-XR YANG model which is currently limited, e.g. it doesn’t support SMU package installation. Although limited, the Cisco IOS-XR YANG definitions will continue to grow as more definitions are added and would be a preferred method for accessing IOS-XR.

Dependencies

manageability (mgbl) and security (k9sec) packages are required on IOS-XR.
Pull YDK from the github onto a Linux server
- git clone https://github.com/CiscoDevNet/ydk-py
Pull Ansible Core modules onto a Linux server
- git clone git://github.com/ansible/ansible.git --recursive
Additional read on Ansible installation is here
- http://docs.ansible.com/ansible/intro_installation.html#getting-ansible

Directories structure

iosxr-ansible
├── config
├── local
│   ├── common
│   ├── library
│   └── samples
│       ├── cli
│       ├── tpnns
│       ├── xml
│       └── ydk
└── remote
    ├── library
    └── samples
        └── install

Directory               Description

config                  Contains sample IOS-XR configuration files
local/library           Contains Ansible modules for local mode
local/samples/cli       Contains sample playbooks using Console CLI
local/samples/tpnns     Contains sample playbooks using TPNNS access method
local/samples/xml       Contains sample RPC XML used with iosxr_netconf_send
local/samples/ydk       Contains sample playbooks using YDK API's
local/common            Contains IOS-XR common Python functions
remote/library          Contains Ansible modules for remote mode
remote/samples          Contains sample playbooks using Namespace Shell CLI
remote/samples/install  Contains additional playbooks showing direct access
                        to IOS-XR using shell

IOS-XR setup

NOTE: Some of these instruction may require root access for setting IOS-XR.

Create default crypto key on your XRV9K VMs (select default 2048 bits)

  RP/0/RP0/CPU0:ios# crypto key generate rsa 
  RP/0/RP0/CPU0:ios# show crypto key mypubkey rsa

Configure IOS-XR as shown in ss1.cfg and ss2.cfg for both XRV9K VMs. Make any necessary changes, such as, management IP address and hostname Here are required configuration

  RP/0/RP0/CPU0:ios# conf t
  RP/0/RP0/CPU0:ios(config)# ssh server v2
  RP/0/RP0/CPU0:ios(config)# ssh server netconf vrf default
  RP/0/RP0/CPU0:ios(config)# ssh server logging
  RP/0/RP0/CPU0:ios(config)# xml agent ssl
  RP/0/RP0/CPU0:ios(config)# xml agent tty
  RP/0/RP0/CPU0:ios(config)# netconf agent tty
  RP/0/RP0/CPU0:ios(config)# netconf-yang agent ssh
  RP/0/RP0/CPU0:ios(config)# commit

Optional SSH key setup allows user to connect to IOS-XR without password. First, generate base64 SSH key file on Ansible Server and copy it to your tftpboot directory.

  cut -d" " -f2 ~/.ssh/id_rsa.pub | base64 -d > ~/.ssh/id_rsa_pub.b64
  cp ~/.ssh/id_rsa_pub.b64 /tftpboot

After IOS-XR is ready, at IOS-XR console prompt, import SSH key as followed

  RP/0/RP0/CPU0:ios# crypto key import authentication rsa tftp://192.168.1.1/id_rsa_pub.b64
  RP/0/RP0/CPU0:ios# show crypto key authentication rsa

Now make sure you can connect to both XRV9K VMs management port from Linux host

  ssh [email protected]
  ssh [email protected] "show run"

Setup the third party namespace (TPNNS) access on IOS-XR. Please refer to the following link for instruction and make sure you can SSH to the IOS-XR through port 57722.

http://www.cisco.com/c/en/us/td/docs/iosxr/AppHosting/b-application-hosting-configuration-guide/AH_User_Guide_chapter_00.html

To access IOS-XR without password, you will also need to add your Linux server SSH public key (~/.ssh/id_rsa.pub) to your IOS-XR <your_xr_home>/.ssh/authorized_key file by using ssh-copy-id command, for example,

  ssh-copy-id -i ~/.ssh/id_rsa.pub -p 57722 [email protected]

If your Linux server support HTTPS and you want a secure communication during SMU package installation, you can import your certificate from Linux to IOS-XR. The IOS-XR certificate store is in /etc/ssl/certs/ca-certificates.crt. Basically, you just need to cut and paste your certificate text to this file.

Local mode setup and test

Edit and source Ansible, YDK, and Python environment to point to your installed applications

  cd iosxr-ansible/local
  vi ansible_env
  source ansible_env

Edit "ansible_hosts" file to change "ss-xr" host IP to your 2 XRV9K VMs

  [ss-xr]
  192.168.1.120 ansible_ssh_user=cisco
  192.168.1.121 ansible_ssh_user=cisco

Run sample playbooks
- Some of sample playbooks will require changes to fit your need e.g. edit iosxr_install_package.yml to change location of your package.

  cd samples
  ansible-playbook iosxr_get_config.yml
  ansible-playbook iosxr_clear_log.yml
  ansible-playbook iosxr_cli.yml -e 'cmd="show interface brief"'
  ansible-playbook iosxr_netconf_send.yml -e "xml_file=xml/nc11_show_install_active.xml"

Remote mode setup and test

Configure Ansible configuration to use port 57722 by editing your ansible config file (default is /etc/ansible/ansible.cfg) with following values

    [defaults]
    remote_port = 57722

Edit Ansible and Python environment as needed in ansible_env and source it

  cd iosxr-ansible/remote
  vi ansible_env
  source ansible_env

Edit "ansible_hosts" file to change "ss-xr" host IP to your 2 XRV9K VMs

  [ss-xr]
  192.168.1.120 ansible_ssh_user=cisco
  192.168.1.121 ansible_ssh_user=cisco

Run sample playbooks
- Some of sample playbooks will require changes to fit your need e.g. edit iosxr_install_package.yml to change location of your package.

  cd samples
  ansible-playbook iosxr_get_config.yml
  ansible-playbook iosxr_cli.yml -e 'cmd="show interface brief"'

Local Mode Modules Description

iosxr_clear_config - Clear all configurations on IOS-XR device
iosxr_clear_log - Clear system log
iosxr_cli - Run a command on IOS-XR device
iosxr_diff_config - Compare a given configuration file with the running configuration
iosxr_get_config - Show running configuration on IOS-XR device
iosxr_get_facts - Get status and information from IOS-XR device
iosxr_install_config - Commit a configuration file on IOS-XR device
iosxr_install_key - Install BASE64 crypto key on IOS-XR device
iosxr_install_package - Install SMU package on IOS-XR device
iosxr_nc10_send - Send NETCONF 1.0 XML file to IOS-XR device
iosxr_nc11_send - Send NETCONF-YANG 1.1 XML file to IOS-XR device
iosxr_reload - Reload IOS-XR device
iosxr_rollback - Rollback configuration on IOS-XR device
iosxr_upgrade_package - Upgrade packages on IOS-XR device
iosxr_xml_send - Performs Cisco XML request to IOS-XR device
xr32_install_package - Run install commands on IOS-XR device

Sample Modules using Cisco YDK services

iosxr_show_install_active - show active package
iosxr_show_install_committed - show committed package
iosxr_show_install_inactive - show inactive package in the repository
iosxr_show_install_last_log - show installation log
iosxr_show_install_log - show installation log
iosxr_show_install_request - show current install request
iosxr_show_install_version - show current software install version

Remote Mode Modules Description

iosxr_clear_log - Clear system log
iosxr_cli - Run a command on IOS-XR device
iosxr_get_config - Show running configuration on IOS-XR device
iosxr_get_facts - Get status and information from IOS-XR device
iosxr_install_config - Commit configuration file on IOS-XR device
iosxr_install_package - Install SMU package on IOS-XR device
iosxr_reload - Reload IOS-XR device
iosxr_rollback - Rollback configuration on IOS-XR device

IOS-XR platforms tested

XRv9K (sunstone)
ASR9K (classic 32-bit QNX IOS-XR)
NCS1K (rosco)
NCS5500 (fretta)

Ansible Test Setup

1 or more IOS-XR device(s)
1 Linux server (ubuntu 15.10)
Create network connection between IOS-XR device and Linux server

Name		Name	Last commit message	Last commit date
Latest commit History 7 Commits
config		config
local		local
meta		meta
remote		remote
LICENSE		LICENSE
README.md		README.md

Provide feedback

Saved searches

Use saved searches to filter your results more quickly

Repository files navigation

Introduction to IOS-XR Ansible

Understand connection variants

Dependencies

Directories structure

IOS-XR setup

Local mode setup and test

Remote mode setup and test

Local Mode Modules Description

Remote Mode Modules Description

IOS-XR platforms tested

Ansible Test Setup

About

Releases 8

Packages

Contributors 2

Languages

License

ios-xr/iosxr-ansible

Folders and files

Latest commit

History

Repository files navigation

Introduction to IOS-XR Ansible

Understand connection variants

Dependencies

Directories structure

IOS-XR setup

Local mode setup and test

Remote mode setup and test

Local Mode Modules Description

Remote Mode Modules Description

IOS-XR platforms tested

Ansible Test Setup

About

Resources

License

Stars

Watchers

Forks

Releases 8

Packages 0

Contributors 2

Languages

Packages