Issues

• Feature request: fillet corner setback and G2 corners

  enhancement
  andymai/brepkit#2201 · Filter by author andymai opened on Oct 30, 2026

• Feature request: blend surface between two edge chains, and fair and match

  enhancement
  andymai/brepkit#2200 · Filter by author andymai opened on Oct 30, 2026

• Feature request: loft guide rails and end conditions

  enhancement
  andymai/brepkit#2199 · Filter by author andymai opened on Oct 30, 2026

• A shell measures no area and can't be meshed

  bug
  andymai/brepkit#2196 · Filter by author andymai opened on Oct 30, 2026

• Booleans of a ring on a tube's rim fall back to a mesh

  bug
  andymai/brepkit#2193 · Filter by author andymai opened on Oct 30, 2026

• Extrude, revolve, and loft fail on an open wire, and sweep gives the wrong surface

  bug
  andymai/brepkit#2192 · Filter by author andymai opened on Oct 30, 2026

• split cuts with a face tool's whole surface, and returns a face lying on the body as a solid

  bug
  andymai/brepkit#2189 · Filter by author andymai opened on Oct 30, 2026

• Hidden-line projection misses edges hidden by another solid or lump

  bug
  andymai/brepkit#2185 · Filter by author andymai opened on Oct 30, 2026

• A cut that leaves separate pieces returns them all in one shell

  bug
  andymai/brepkit#2184 · Filter by author andymai opened on Oct 30, 2026

• Revolving a face with a hole gives a solid of the wrong volume

  bug
  andymai/brepkit#2183 · Filter by author andymai opened on Oct 30, 2026

• IGES export writes each face as an unbounded plane, so a solid does not survive a round trip

  bug
  andymai/brepkit#2179 · Filter by author andymai opened on Oct 30, 2026

• Revolving a disc about an axis tangent to it fails, and torus(5, 5) is rejected

  bug
  andymai/brepkit#2178 · Filter by author andymai opened on Oct 30, 2026

• simplify leaves a primitive sphere as two faces after an intersect, 8 faces where 7 are expected

  bug
  andymai/brepkit#2176 · Filter by author andymai opened on Oct 30, 2026

• draft rejects a pocket with curved walls: "draft target faces must be planar"

  bug
  andymai/brepkit#2174 · Filter by author andymai opened on Oct 30, 2026

• Sweeping a circle along a helix gives 1766 faces and a volume 2.7% low

  bug
  andymai/brepkit#2170 · Filter by author andymai opened on Oct 30, 2026

• A loft from a square to a circle facets the circle, and a loft to a point leaves a zero-area cap

  bug
  andymai/brepkit#2169 · Filter by author andymai opened on Oct 30, 2026

• A cut that splits a solid in two returns one solid with one shell

  bug
  andymai/brepkit#2167 · Filter by author andymai opened on Oct 30, 2026

• Exact booleans fall back to a faceted mesh in seven simple configurations

  bug
  andymai/brepkit#2166 · Filter by author andymai opened on Oct 30, 2026

• A full revolve splits faces into 90° bands, and booleans against the banded sphere fall back to a mesh

  bug
  andymai/brepkit#2165 · Filter by author andymai opened on Oct 30, 2026

• Chamfering an obround prism fails along its loop, and one edge alone halves the solid

  bug
  andymai/brepkit#2163 · Filter by author andymai opened on Oct 30, 2026

• Fillets fail on a flat box's edges together, on a saddle edge, and on an edge that ends at a concave corner

  bug
  andymai/brepkit#2161 · Filter by author andymai opened on Oct 30, 2026