diff --git a/examples/STSCL/MultiControl/MultiControl.ino b/examples/STSCL/MultiControl/MultiControl.ino
new file mode 100644
index 0000000..c1c5409
--- /dev/null
+++ b/examples/STSCL/MultiControl/MultiControl.ino
@@ -0,0 +1,88 @@
+#include <SCServo.h>
+
+#if defined(CONFIG_IDF_TARGET_ESP32C3) || defined(CONFIG_IDF_TARGET_ESP32C6) || defined(CONFIG_IDF_TARGET_ESP32S3)
+#define COMSerial Serial0
+#else
+#define COMSerial Serial1
+#endif
+
+#if defined(NRF52840_XXAA) && defined(USE_TINYUSB)
+#include <Adafruit_TinyUSB.h>
+#endif
+
+#define S_RXD D7
+#define S_TXD D6
+#define Servo_Num 6
+
+SMS_STS st;
+byte ID[Servo_Num] = {1, 2, 3, 4, 5, 6};
+u16 Speed[Servo_Num] = {3400, 3400, 3400, 3400, 3400, 3400};
+byte ACC[Servo_Num] = {253, 253, 253, 253, 253, 253};
+s16 Pos[Servo_Num] = {0, 0, 0, 0, 0, 0};
+
+int getPos(int id)
+{
+  return st.ReadPos(id);
+}
+
+void setup()
+{
+  Serial.begin(115200);
+
+  COMSerial.begin(1000000, SERIAL_8N1);
+  st.pSerial = &COMSerial;
+  delay(1000);
+
+  Serial.println("Calibration of all Servo");
+  for (int i = 0; i < Servo_Num; i++) {
+    st.CalibrationOfs(ID[i]);
+  }
+
+  for (int i = 0; i < Servo_Num; i++) {
+    Pos[i] = getPos(ID[i]);
+  }
+
+  delay(1000);
+}
+
+void loop()
+{
+  if (!Serial.available()) {
+    delay(100);
+    return;
+  }
+
+  String input = Serial.readString();
+  input.trim();
+
+  if(input.startsWith("j")) {
+    Serial.println("Reduce the angle");
+
+    for (int i = 0; i < Servo_Num; i++) {
+      if (Pos[i] == 0) {
+        Serial.print(i);
+        Serial.println(" It's already in the minimum position.");
+        continue;
+      }
+
+      Pos[i] -= 1024;
+      if (Pos[i] < 0) Pos[i] = 0;
+    }
+  } else if(input.startsWith("k")) {
+    Serial.println("Increase the angle");
+
+    for (int i = 0; i < Servo_Num; i++) {
+      if (Pos[i] == 4095) {
+        Serial.print(i);
+        Serial.println(" It's already in the maximum position.");
+        continue;
+      }
+
+      Pos[i] += 1024;
+      if (Pos[i] > 4095) Pos[i] = 4095;
+    }
+  }
+
+  st.SyncWritePosEx(ID, Servo_Num, Pos, Speed, ACC);
+  delay(600);
+}