diff --git a/docs/configuration/protocols/index.rst b/docs/configuration/protocols/index.rst
index 29dc230f89..237608a183 100644
--- a/docs/configuration/protocols/index.rst
+++ b/docs/configuration/protocols/index.rst
@@ -16,6 +16,7 @@ Protocols
    mpls
    segment-routing
    ospf
+   pim6
    rip
    rpki
    static
diff --git a/docs/configuration/protocols/pim6.rst b/docs/configuration/protocols/pim6.rst
new file mode 100644
index 0000000000..56cc33c07c
--- /dev/null
+++ b/docs/configuration/protocols/pim6.rst
@@ -0,0 +1,74 @@
+.. _pim6:
+
+#####
+IPv6 Multicast
+#####
+
+VyOS facilitates IPv6 Multicast by supporting **PIMv6** and **MLD**.
+
+PIMv6 (Protocol Independent Multicast for IPv6) must be configured in every
+interface of every participating router. Every router must also have the
+location of the Rendevouz Point manually configured.
+Then, unidirectional shared trees rooted at the Rendevouz Point will
+automatically be built for multicast distribution.
+
+Traffic from multicast sources will go to the Rendezvous Point, and receivers
+will pull it from a shared tree using MLD (Multicast Listener Discovery).
+
+Multicast receivers will talk MLD to their local router, so, besides having
+PIMv6 configured in every router, MLD must also be configured in any router
+where there could be a multicast receiver locally connected.
+
+VyOS supports both MLD version 1 and version 2
+(which allows source-specific multicast).
+
+Basic commands
+==============
+These are the commands for a basic setup.
+
+.. cfgcmd:: set protocols pim6 interface <interface-name>
+
+   Use this command to enable PIMv6 in the selected interface so that it
+   can communicate with PIMv6 neighbors. This command also enables MLD reports
+   and query on the interface unless :cfgcmd:`mld disable` is configured.
+
+.. cfgcmd:: set protocols pim6 interface <interface-name> mld disable
+
+   Disable MLD reports and query on the interface.
+
+
+Tuning commands
+===============
+You can also tune multicast with the following commands.
+
+
+.. cfgcmd:: set protocols pim6 interface <interface-name> mld interval <seconds>
+
+   Use this command to configure in the selected interface the MLD
+   host query interval (1-65535) in seconds that PIM will use.
+   The default value is 125 seconds.
+
+.. cfgcmd:: set protocols pim6 interface <interface-name> mld join <multicast-address>
+
+   Use this command to allow the selected interface to join a multicast group.
+
+.. cfgcmd:: set protocols pim6 interface <interface-name> mld join <multicast-address> source <source-address>
+
+   Use this command to allow the selected interface to join a source-specific multicast
+   group.
+
+.. cfgcmd:: set protocols pim6 interface <interface-name> mld last-member-query-count <count>
+
+   Set the MLD last member query count. The default value is 2.
+
+.. cfgcmd:: set protocols pim6 interface <interface-name> mld last-member-query-interval <milliseconds>
+
+   Set the MLD last member query interval in milliseconds (100-6553500). The default value is 1000 milliseconds.
+
+.. cfgcmd:: set protocols pim6 interface <interface-name> mld max-response-time <milliseconds>
+
+   Set the MLD query response timeout in milliseconds. The default value is 10000 milliseconds.
+
+.. cfgcmd:: set protocols pim6 interface <interface-name> mld version <version-number>
+
+   Set the MLD version used on this interface. The default value is 2.