Can't connect to ONE+

[chobblars87]

Hey Stanley,

I've had my device for some time, but have never managed to actually connect to it. I've enabled Bluetooth, and turned off the OBD temporarily just to make sure that the device connects to something, but I can't find it on the Freematics app nor does it connect to my WiFi.

Any ideas as to what am I doing wrong?

Thanks,
Paul

Added my entire config.h file below just in case that's of use.

#ifndef CONFIG_H_INCLUDED
#define CONFIG_H_INCLUDED

/**************************************

• Circular Buffer Configuration
  **************************************/

#define BUFFER_SLOTS 32 /* max number of buffer /
#define BUFFER_LENGTH 128 / bytes per slot /
#define SERIALIZE_BUFFER_SIZE 1024 / bytes */

/**************************************

• Configuration Definitions
  **************************************/
  #define NET_WIFI 1
  #define NET_WIFI_MESH 2
  #define NET_SERIAL 3
  #define NET_SIM800 4
  #define NET_SIM5360 5
  #define NET_SIM7600 6
  #define NET_SIM7070 7

#define STORAGE_NONE 0
#define STORAGE_SPIFFS 1
#define STORAGE_SD 2

#define GNSS_NONE 0
#define GNSS_INTERNAL 1
#define GNSS_EXTERNAL 2
#define GNSS_CELLULAR 3

#define PROTOCOL_UDP 1
#define PROTOCOL_HTTP 2
#define PROTOCOL_HTTPS 3

#define PROTOCOL_METHOD_GET 0
#define PROTOCOL_METHOD_POST 1

/**************************************

• OBD-II configurations
  **************************************/
  #ifndef ENABLE_OBD
  #define ENABLE_OBD 0
  #endif

// maximum consecutive OBD access errors before entering standby
#define MAX_OBD_ERRORS 3

/**************************************

• Networking configurations
  **************************************/
  #ifndef NET_DEVICE
  // change the following line to change network device
  #define NET_DEVICE NET_SIM7600
  // WiFi settings
  #define WIFI_SSID "KandB-IoT"
  #define WIFI_PASSWORD "*"
  // cellular network settings
  #define CELL_APN "hologram"
  // Freematics Hub server settings
  #define SERVER_HOST ""
  #define SERVER_PROTOCOL PROTOCOL_UDP
  #endif

// SIM card setting
#define SIM_CARD_PIN ""

// HTTPS settings
#define SERVER_METHOD PROTOCOL_METHOD_POST
#define SERVER_PATH "/hub/api"

#if !SERVER_PORT
#undef SERVER_PORT
#if SERVER_PROTOCOL == PROTOCOL_UDP
#define SERVER_PORT 5170
#elif SERVER_PROTOCOL == PROTOCOL_HTTP
#define SERVER_PORT 80
#elif SERVER_PROTOCOL == PROTOCOL_HTTPS
#define SERVER_PORT 443
#endif
#endif

// WiFi Mesh settings
#define WIFI_MESH_ID "123456"
#define WIFI_MESH_CHANNEL 13

// WiFi AP settings
#define WIFI_AP_SSID "TELELOGGER"
#define WIFI_AP_PASSWORD "PASSWORD"

// maximum consecutive communication errors before resetting network
#define MAX_CONN_ERRORS_RECONNECT 3
// maximum allowed connecting time
#define MAX_CONN_TIME 10000 /* ms /
// data receiving timeout
#define DATA_RECEIVING_TIMEOUT 5000 / ms /
// expected maximum server sync signal interval
#define SERVER_SYNC_INTERVAL 120 / seconds, 0 to disable /
// data interval settings
#define STATIONARY_TIME_TABLE {30, 60, 180} / seconds /
#define DATA_INTERVAL_TABLE {1000, 2000, 5000} / ms /
#define PING_BACK_INTERVAL 900 / seconds */

/**************************************

• Data storage configurations
  **************************************/
  #ifndef STORAGE
  // change the following line to change storage type
  #define STORAGE STORAGE_SD
  #endif

/**************************************

• MEMS sensors
  **************************************/
  #define ENABLE_ORIENTATION 0
  #ifndef ENABLE_MEMS
  #define ENABLE_MEMS 1
  #endif

/**************************************

• GPS
  **************************************/
  #ifndef GNSS
  // change the following line to change GNSS setting
  #define GNSS GNSS_EXTERNAL
  #endif
  #define GNSS_ALWAYS_ON 1

/**************************************

• Standby/wakeup
  *************************************/
  #define RESET_AFTER_WAKEUP 0
  // motion threshold for waking up
  #define MOTION_THRESHOLD 0.4f / moving vehicle motion threshold in G /
  // engine jumpstart voltage
  #define JUMPSTART_VOLTAGE 13.5f / V /
  #define LOW_BATTERY_VOLTAGE 11.6f / V */

/**************************************

• Additional features
  **************************************/
  #define CONFIG_MODE_TIMEOUT 0

#define PIN_SENSOR1 34
#define PIN_SENSOR2 26

#define COOLING_DOWN_TEMP 65 /* celsius degrees */

#define ENABLE_BLE 1
#endif // CONFIG_H_INCLUDED