Closed
Description
Board
ESP32 Dev Module, 8MB Flash
Device Description
ESP32 Dev Module, 8MB flash
Hardware Configuration
8MB ESP32 Dev Module. No attachments
Version
latest master (checkout manually)
IDE Name
Arduino IDE 2.3.2
Operating System
Windows 11
Flash frequency
40MHz
PSRAM enabled
no
Upload speed
921600
Description
I am using 8MB ESP32 Dev Module, with the following IDE settings.
I use arduino IDE 2.3.2 for firmware but go back to 1.8.9 to use the ESP32 Sketch Data Upload Tool using spiffs. This works fine when using the IDE. But if I take the same spiffs file that is generated using the mkspiffs tool, use the webupdater.ino example, and use the Filesystem update option, It throws
Update error: Bad Size Given
Sketch
Examples>WebUpdater.inoDebug Message
rst:0xb (TGWDT_CPU_RESET),boot:0x12 (SPI_FAST_FLASH_BOOT)
configsip: 0, SPIWP:0xee
clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
mode:DIO, clock div:1
load:0x3fff0030,len:1448
load:0x40078000,len:14844
ho 0 tail 12 room 4
load:0x40080400,len:4
load:0x40080404,len:3356
[ 1][V][esp32-hal-periman.c:235] perimanSetBusDeinit(): Deinit function for type UART_RX (2) successfully set to 0x400e4838
[ 12][V][esp32-hal-periman.c:235] perimanSetBusDeinit(): Deinit function for type UART_TX (3) successfully set to 0x400e4808
[ 26][V][esp32-hal-periman.c:235] perimanSetBusDeinit(): Deinit function for type UART_CTS (4) successfully set to 0x400e47d8
[ 39][V][esp32-hal-periman.c:235] perimanSetBusDeinit(): Deinit function for type UART_RTS (5) successfully set to 0x400e47a8
[ 53][V][esp32-hal-periman.c:235] perimanSetBusDeinit(): Deinit function for type UART_RX (2) successfully set to 0x400e4838
[ 66][V][esp32-hal-periman.c:235] perimanSetBusDeinit(): Deinit function for type UART_TX (3) successfully set to 0x400e4808
[ 79][V][esp32-hal-periman.c:235] perimanSetBusDeinit(): Deinit function for type UART_CTS (4) successfully set to 0x400e47d8
[ 93][V][esp32-hal-periman.c:235] perimanSetBusDeinit(): Deinit function for type UART_RTS (5) successfully set to 0x400e47a8
[ 106][V][esp32-hal-periman.c:235] perimanSetBusDeinit(): Deinit function for type UART_RX (2) successfully set to 0x400e4838
[ 120][V][esp32-hal-periman.c:235] perimanSetBusDeinit(): Deinit function for type UART_TX (3) successfully set to 0x400e4808
[ 133][V][esp32-hal-periman.c:235] perimanSetBusDeinit(): Deinit function for type UART_CTS (4) successfully set to 0x400e47d8
[ 147][V][esp32-hal-periman.c:235] perimanSetBusDeinit(): Deinit function for type UART_RTS (5) successfully set to 0x400e47a8
[ 160][V][NetworkServer.h:41] NetworkServer(): NetworkServer::NetworkServer(port=80, ...)
[ 171][V][WebServer.cpp:55] WebServer(): WebServer::Webserver(port=80)
[ 181][D][esp32-hal-cpu.c:264] setCpuFrequencyMhz(): PLL: 480 / 2 = 240 Mhz, APB: 80000000 Hz
[ 235][V][esp32-hal-periman.c:160] perimanSetPinBus(): Pin 3 successfully set to type UART_RX (2) with bus 0x3ffbdb7c
[ 246][V][esp32-hal-periman.c:160] perimanSetPinBus(): Pin 1 successfully set to type UART_TX (3) with bus 0x3ffbdb7c
entry 0x4008059c
[ 235][V][esp32-hal-periman.c:160] perimanSetPinBus(): Pin 3 successfully set to type UART_RX (2) with bus 0x3ffbdb7c
[ 246][V][esp32-hal-periman.c:160] perimanSetPinBus(): Pin 1 successfully set to type UART_TX (3) with bus 0x3ffbdb7c
=========== Before Setup Start ===========
Chip Info:
------------------------------------------
Model : ESP32
Package : D0WD-Q5
Revision : 101
Cores : 2
CPU Frequency : 240 MHz
XTAL Frequency : 40 MHz
Embedded Flash : No
Embedded PSRAM : No
2.4GHz WiFi : Yes
Classic BT : Yes
BT Low Energy : Yes
IEEE 802.15.4 : No
------------------------------------------
INTERNAL Memory Info:
------------------------------------------
Total Size : 333752 B ( 325.9 KB)
Free Bytes : 303112 B ( 296.0 KB)
Allocated Bytes : 23512 B ( 23.0 KB)
Minimum Free Bytes: 297596 B ( 290.6 KB)
Largest Free Block: 110580 B ( 108.0 KB)
------------------------------------------
Flash Info:
------------------------------------------
Chip Size : 8388608 B (8 MB)
Block Size : 65536 B ( 64.0 KB)
Sector Size : 4096 B ( 4.0 KB)
Page Size : 256 B ( 0.2 KB)
Bus Speed : 80 MHz
Bus Mode : QIO
------------------------------------------
Partitions Info:
------------------------------------------
nvs : addr: 0x00009000, size: 20.0 KB, type: DATA, subtype: NVS
otadata : addr: 0x0000E000, size: 8.0 KB, type: DATA, subtype: OTA
app0 : addr: 0x00010000, size: 3264.0 KB, type: APP, subtype: OTA_0
app1 : addr: 0x00340000, size: 3264.0 KB, type: APP, subtype: OTA_1
spiffs : addr: 0x00670000, size: 1536.0 KB, type: DATA, subtype: SPIFFS
coredump : addr: 0x007F0000, size: 64.0 KB, type: DATA, subtype: COREDUMP
------------------------------------------
Software Info:
------------------------------------------
Compile Date/Time : Jun 30 2024 10:49:12
Compile Host OS : windows
ESP-IDF Version : v5.1.4-358-gbd2b9390ef-dirty
Arduino Version : 3.0.2
------------------------------------------
Board Info:
------------------------------------------
Arduino Board : ESP32_DEV
Arduino Variant : esp32
Arduino FQBN : espressif:esp32:esp32:UploadSpeed=921600,CPUFreq=240,FlashFreq=80,FlashMode=qio,FlashSize=8M,PartitionScheme=default_8MB,DebugLevel=verbose,PSRAM=enabled,LoopCore=1,EventsCore=1,EraseFlash=none,JTAGAdapter=default,ZigbeeMode=default
============ Before Setup End ============
[ 754][V][esp32-hal-uart.c:408] uartBegin(): UART0 baud(115200) Mode(800001c) rxPin(3) txPin(1)
[ 762][V][esp32-hal-uart.c:497] uartBegin(): UART0 not installed. Starting installation
[ 773][V][esp32-hal-uart.c:544] uartBegin(): UART0 initialization done.
Booting Sketch...
[ 804][V][NetworkEvents.cpp:119] checkForEvent(): Network Event: 9 - WIFI_READY
[ 884][V][STA.cpp:184] _onStaEvent(): STA Started
[ 889][V][NetworkEvents.cpp:119] checkForEvent(): Network Event: 11 - STA_START
[ 890][V][AP.cpp:106] _onApEvent(): AP Started
[ 901][V][STA.cpp:110] _onStaArduinoEvent(): Arduino STA Event: 11 - STA_START
[ 908][V][NetworkEvents.cpp:119] checkForEvent(): Network Event: 19 - AP_START
[ 915][V][AP.cpp:88] _onApArduinoEvent(): Arduino AP Event: 19 - AP_START
[ 995][V][STA.cpp:204] _onStaEvent(): STA Connected: SSID: Hanger6, BSSID: d8:a7:56:00:5e:96, Channel: 1, Auth: WPA2_PSK
[ 1006][V][NetworkEvents.cpp:119] checkForEvent(): Network Event: 13 - STA_CONNECTED
[ 1014][V][STA.cpp:110] _onStaArduinoEvent(): Arduino STA Event: 13 - STA_CONNECTED
[ 1220][V][NetworkInterface.cpp:66] _onIpEvent(): sta Got New IP: 192.168.2.44 MASK: 255.255.255.0 GW: 192.168.2.1
[ 1230][V][NetworkEvents.cpp:119] checkForEvent(): Network Event: 16 - STA_GOT_IP
[ 1238][V][STA.cpp:110] _onStaArduinoEvent(): Arduino STA Event: 16 - STA_GOT_IP
[ 1245][V][STA.cpp:169] _onStaArduinoEvent(): STA IP: 192.168.2.44, MASK: 255.255.255.0, GW: 192.168.2.1
mDNS responder started
HTTPUpdateServer ready! Open http://esp32-webupdate.local/update in your browser
=========== After Setup Start ============
INTERNAL Memory Info:
------------------------------------------
Total Size : 333752 B ( 325.9 KB)
Free Bytes : 237292 B ( 231.7 KB)
Allocated Bytes : 85500 B ( 83.5 KB)
Minimum Free Bytes: 237148 B ( 231.6 KB)
Largest Free Block: 110580 B ( 108.0 KB)
------------------------------------------
GPIO Info:
------------------------------------------
GPIO : BUS_TYPE[bus/unit][chan]
--------------------------------------
1 : UART_TX[0]
3 : UART_RX[0]
============ After Setup End =============
When trying to access /update
[ 9521][V][Parsing.cpp:257] _parseRequest(): headerValue: 1
[ 9527][V][Parsing.cpp:256] _parseRequest(): headerName: User-Agent
[ 9533][V][Parsing.cpp:257] _parseRequest(): headerValue: Mozilla/5.0 (Windows NT 10.0; Win64; x64) AppleWebKit/537.36 (KHTML, like Gecko) Chrome/126.0.0.0 Safari/537.36
[ 9548][V][Parsing.cpp:256] _parseRequest(): headerName: Accept
[ 9554][V][Parsing.cpp:257] _parseRequest(): headerValue: text/html,application/xhtml+xml,application/xml;q=0.9,image/avif,image/webp,image/apng,*/*;q=0.8
[ 9568][V][Parsing.cpp:256] _parseRequest(): headerName: Sec-GPC
[ 9574][V][Parsing.cpp:257] _parseRequest(): headerValue: 1
[ 9579][V][Parsing.cpp:256] _parseRequest(): headerName: Accept-Language
[ 9586][V][Parsing.cpp:257] _parseRequest(): headerValue: en-US,en
[ 9592][V][Parsing.cpp:256] _parseRequest(): headerName: Accept-Encoding
[ 9599][V][Parsing.cpp:257] _parseRequest(): headerValue: gzip, deflate
[ 9605][V][Parsing.cpp:284] _parseArguments(): args:
[ 9610][V][Parsing.cpp:267] _parseRequest(): Request: /update
[ 9616][V][Parsing.cpp:268] _parseRequest(): Arguments:
When selecting SPIFFS FILE and submitting
[ 22886][V][WebServer.cpp:418] handleClient(): New client: client.localIP()=192.168.2.44
[ 22895][V][Parsing.cpp:122] _parseRequest(): method: POST url: /update search:
[ 22902][V][Parsing.cpp:157] _parseRequest(): headerName: Host
[ 22908][V][Parsing.cpp:158] _parseRequest(): headerValue: 192.168.2.44
[ 22915][V][Parsing.cpp:157] _parseRequest(): headerName: Connection
[ 22921][V][Parsing.cpp:158] _parseRequest(): headerValue: keep-alive
[ 22927][V][Parsing.cpp:157] _parseRequest(): headerName: Content-Length
[ 22934][V][Parsing.cpp:158] _parseRequest(): headerValue: 1573078
[ 22940][V][Parsing.cpp:157] _parseRequest(): headerName: Cache-Control
[ 22946][V][Parsing.cpp:158] _parseRequest(): headerValue: max-age=0
[ 22953][V][Parsing.cpp:157] _parseRequest(): headerName: Upgrade-Insecure-Requests
[ 22960][V][Parsing.cpp:158] _parseRequest(): headerValue: 1
[ 22966][V][Parsing.cpp:157] _parseRequest(): headerName: Origin
[ 22971][V][Parsing.cpp:158] _parseRequest(): headerValue: http://192.168.2.44
[ 22979][V][Parsing.cpp:157] _parseRequest(): headerName: Content-Type
[ 22985][V][Parsing.cpp:158] _parseRequest(): headerValue: multipart/form-data; boundary=----WebKitFormBoundaryy3LOPt4U4nibX6GB
[ 22997][V][Parsing.cpp:157] _parseRequest(): headerName: User-Agent
[ 23003][V][Parsing.cpp:158] _parseRequest(): headerValue: Mozilla/5.0 (Windows NT 10.0; Win64; x64) AppleWebKit/537.36 (KHTML, like Gecko) Chrome/126.0.0.0 Safari/537.36
[ 23019][V][Parsing.cpp:157] _parseRequest(): headerName: Accept
[ 23024][V][Parsing.cpp:158] _parseRequest(): headerValue: text/html,application/xhtml+xml,application/xml;q=0.9,image/avif,image/webp,image/apng,*/*;q=0.8
[ 23038][V][Parsing.cpp:157] _parseRequest(): headerName: Sec-GPC
[ 23044][V][Parsing.cpp:158] _parseRequest(): headerValue: 1
[ 23050][V][Parsing.cpp:157] _parseRequest(): headerName: Accept-Language
[ 23056][V][Parsing.cpp:158] _parseRequest(): headerValue: en-US,en
[ 23063][V][Parsing.cpp:157] _parseRequest(): headerName: Referer
[ 23069][V][Parsing.cpp:158] _parseRequest(): headerValue: http://192.168.2.44/update
[ 23076][V][Parsing.cpp:157] _parseRequest(): headerName: Accept-Encoding
[ 23083][V][Parsing.cpp:158] _parseRequest(): headerValue: gzip, deflate
[ 23090][V][Parsing.cpp:284] _parseArguments(): args:
[ 23095][V][Parsing.cpp:362] _parseForm(): Parse Form: Boundary: ----WebKitFormBoundaryy3LOPt4U4nibX6GB Length: 1573078
[ 23106][V][Parsing.cpp:398] _parseForm(): PostArg FileName: DataFile.bin
[ 23113][V][Parsing.cpp:404] _parseForm(): PostArg Name: filesystem
[ 23120][V][Parsing.cpp:417] _parseForm(): PostArg Type: application/octet-stream
[ 23127][V][Parsing.cpp:451] _parseForm(): Start File: DataFile.bin Type: application/octet-stream
[ 27426][V][Parsing.cpp:499] _parseForm(): End File: DataFile.bin Type: application/octet-stream Size: 1572864
[ 27436][V][Parsing.cpp:506] _parseForm(): Done Parsing POST
[ 27442][V][Parsing.cpp:267] _parseRequest(): Request: /update
[ 27447][V][Parsing.cpp:268] _parseRequest(): Arguments:
On the webpage,
Update error: Bad Size Given
Other Steps to Reproduce
Tried on few different boards, similar result.
I have checked existing issues, online documentation and the Troubleshooting Guide
- I confirm I have checked existing issues, online documentation and Troubleshooting guide.
Metadata
Metadata
Assignees
Labels
No labels