forked from emmebrusa/TSDZ2-Smart-EBike-1
-
Notifications
You must be signed in to change notification settings - Fork 1
/
changelog.txt
128 lines (119 loc) · 6.93 KB
/
changelog.txt
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
TSDZ2 Open Source Firmware
for stock displays XH18 - VLCD5 - VLCD6
List of changes v20.1C.6-beta-1
1 - Moved ERROR MOTOR CHECK to E09, shared with ERROR WRITE EEPROM.
2 - Fixed power limit issue and others bugs.
3 - Debugging workflow (by @dzid26).
4 - Motor goes alone fixes (by @dzid26).
5 - Cut PWM above speed limit, fixes E09 (by @dzid26).
List of changes v20.1C.6-beta-0
1 - Updated to v15 version of mspider65 (optimized FOC angle calculation)
2 - Added "Smooth start" feature for Hybrid, Torque and Cadence mode.
3 - Progressive assist in eMtb mode, based on torque or power.
4 - Levels set the current target in Cadence Assist mode.
5 - Optimized PID parameters in Cruise mode.
6 - Enabling Coaster Brake disables Walk Assist, Startup Assist, Throttle, Cruise (safety).
7 - Startup assist. Added speed limit to 6 km/h.
8 - Choice of temperature sensor, LM35 or TMP36.
9 - Choice of brake input, brake sensors or on/off thermostat (NO max 85°C).
10 - Choice of throttle use mode.
11 - Convert mph and miles to VLCD6, or alternative for other displays.
12 - Added motor overcurrent check (by mspider65), E07 overcurrent error.
13 - Added throttle input check on power up, E05 throttle fault.
14 - Fixed walk assist debounce time issue.
15 - Fixed torque sensor calibration problem with weight.
16 - Improved field weakening feature.
17 - For 32-bit Windows, auto switching to the 32-bit Cygwin folder.
18 - Added terminal for Compiling&Flash output in Linux (xterm required).
19 - Developer tools (by @dzid26).
List of changes v20.1C.2 update 3
1 - Fix Makefile clear_eeprom with -s eeprom (by @apolselli)
2 - Fix compiler warning for missing void in function prototypes (by @chgpalmer)
3 - Improved building (by @dzid26)
4 - Irq uart priority level set
List of changes v20.1C.2 update 2
1 - Improved Walk assist speed adjustment.
2 - Added legal throttle, only works when pedaling, in street mode.
3 - Added 850C display support (6 pin connector & TSDZ2 protocol).
4 - Added fifth level, for display with 5 levels.
5 - Fixed data display with units = miles.
6 - Fixed Startup assist max time (10 sec).
7 - Fixed comms error detection (by lcha78).
8 - Added manuals in Spanish (by ashrambo).
9 - Building script improvements (by dzid26)
10 - Compile and flash automatically from Linux and Mac OS (by IArchi)
11 - VLCD6, fixed SOC display at power on
List of changes v20.1C.2 update 1
1 - Fixed "Startup assist" feature.
2 - Assist without pedaling, can also be activated with negative torque offset.
3 - E08 error speed sensor failure, disabled in Walk assist mode.
4 - E05 error motor check, monitoring time increased.
List of changes v20.1C.2
1 - Added "Motor deceleration", adjustable 0-100%.
2 - Improved torque sensor calibration.
3 - Added adjustment of the adc offset of the pedal torque.
4 - Added adjustment of the adc range of the pedal torque.
5 - Added adjustment of the adc angle of the pedal torque.
6 - Added estimated calculation "Pedal torque adc step".
7 - Added "Startup assist", for starting from a stationary on difficult climbs.
8 - Added "Walk Assist" speed settings, one for each level.
9 - Added choice Startup boost mode, at zero cadence or at zero speed.
10 - Improved progressivity in "Cadence Assist" mode.
11 - Added choice of soc % calculation mode.
12 - Improved the problem of delay in restarting with bike in motion (from mspider65 v12)
13 - Modified standing start, softer.
14 - Fixed an overflow issue in power assist mode.
15 - Fixed calculation of human power.
16 - Fixed, coaster brake feature.
17 - Display of TE and TE1 torque sensor values (VLCD5 only).
18 - Changed "dead time" value to 2.0 us.
19 - Cross-check motor current variables, with assistance stop in the presence of incompatible values (possible cause of motor operation without pedaling).
List of changes v20.1C.1
1 - Torque sensor calibration bug fixed.
2 - Overtemperature problem at high power fixed.
3 - Eliminated potential mosfet risk in "save battery capacity".
4 - Eliminated potential phantom pedaling risk in "rx buffer".
5 - Changed "dead time" value to 1.5 us.
6 - Torque offset fix.
List of changes v20.1C
1 - Added field weakening function to increase the motor speed (by mspider65).
2 - Added other optimizations to motor control, torque sensor and cadence sensor (by mspider65).
3 - Added startup boost function in POWER assist mode, enable/disable at display.
4 - Added HYBRID assist mode, TORQUE + POWER, can be set on the display.
5 - Improved "Start-up without pedal rotation" function.
6 - Added a filter to the speed sensor to avoid problems of adjusting the distance from the magnet.
7 - Added error E08 due to speed sensor failure or missing magnet.
8 - Added error E03 cadence sensor failure.
9 - Added "Assist with sensors error" function, to force assistance with sensors problem.
10 - Changed the manual reset of battery soc, now more accurate.
11 - Changed the voltage detection for battery bars, the battery resistance is no longer used, (by kaltekaffe).
12 - Changed "Set parameters" function on display.
13 - Added display of the status of the selected parameter.
14 - Removed flashing of the options byte file.
15 - Configurator. Added choice of data to be displayed at power on.
16 - Configurator. Added ability to disable "Walk assist" in "Street mode".
17 - Configurator. Added enable/disable and sensitivity of coaster brake.
18 - Configurator. By changing the unit of measurement km/h or mph, all speed values are adjusted.
19 - Configurator. New parameters have been added. Default values are been changed.
20 - Configurator manual and display manual, updated.
List of changes v20.1B
1 - added cadence sensor calibration in advanced mode.
2 - added calibration of maximum torque value (torque sensor range).
3 - added ADC conversion factor calibration of the torque sensor (with weight).
4 - added ADC offset adjustment of the torque sensor.
5 - added choice to display, standard or advanced mode for cadence and torque sensors.
6 - added data display in automatic sequence when the lights are turned on.
7 - added other data that can be shown on the display.
8 - added ability to view data with miles setting.
9 - access to parameters and data also with error code present.
10 - separate definitions, TARGET_MAX_BATTERY_POWER and TARGET_MAX_BATTERY_CAPACITY.
11 - with WALK_ASSIST_DEBO UNCE_TIME, the brake sensors in addition to the motor now also stop time.
12 - CRUISE mode now also operable with walk assist command.
13 - at level 0 = OFF the accelerator is disabled.
14 - moved the parameters for error E04 "motor blocked" to the config.h file.
15 - modified " fix overrun " for a quick stop of the motor when you stop pedaling.
16 - modified the manual reset of the residual battery percentage.
17 - fixed data saving problem in eeprom.
18 - fixed display battery residual percentage problem at startup.
19 - fixed problem displaying error E06 "over temperature".
20 - Stancecoke Java Parameter Configurator completed.