CISCO-WAN-FR-SIGNALING-MIB-V1SMI.my

-- MIB file created 09-Jan-2004 14:10:33, by
--   SMICng version 2.2.11-beta(PRO)(Solaris), January 20, 2001. Enterprise key cisco.com

CISCO-WAN-FR-SIGNALING-MIB DEFINITIONS ::= BEGIN

-- From file: "CISCO-WAN-FR-SIGNALING-MIB.my"
-- Compile options "4 7 F H N W 03 06 0B 0G 0N 0T"

IMPORTS
    frPortCnfSig, frPortCntSig
            FROM BASIS-MIB
    ciscoWan
            FROM CISCOWAN-SMI
    Counter
            FROM RFC1155-SMI
    OBJECT-TYPE
            FROM RFC-1212;

ciscoWanFrSignalingMIB OBJECT IDENTIFIER ::= { ciscoWan 46 }
-- MODULE-IDENTITY
--  LastUpdated
--    200303240000Z
--  OrgName
--    Cisco Systems, Inc.
--  ContactInfo
--           Cisco Systems
--                Customer Service
--    
--        Postal: 170 W Tasman Drive
--                San Jose, CA  95134
--                USA
--    
--                Tel: +1 800 553-NETS
--    
--        E-mail: cs-wanatm@cisco.com
--  Descr
--    The MIB module to configure LMI and CLLM
--    on a frame relay ports. This mib module also
--    contains objects to represent LMI and CLLM
--    statistics information. The frame relay logical
--    port is referred to as 'frame relay port' in this
--    mib. The 'logical port' refers to frame relay
--    port.
--    
--    LMI  : Local Management Interface.
--        The Frame Relay LMI is a set of enhancements to
--        the basic Frame Relay Specification. The Key
--        Frame Relay LMI extensions include global addressing,
--        virtual circuit status messages and multicasting.
--        The LMI includes support for a keepalive mechanism,
--        which verifies that data is flowing, and a status
--        mechanism, which provides an on-going status report
--        on the DLCIs known to the switch.
--    
--        The LMI Global Addressing extension gives Frame Relay
--        DLCI values global rather than local significance.
--        The global addressing extension adds functionality
--        and manageability to Frame Relay internetworks.
--    
--        The LMI virtual circuit messages provide communication
--        and synchronization between Frame Relay DTE and
--        DCE devices. These messages are periodically report
--        on the status of PVCs, which prevents data from being
--        sent into black holes(that, over PVCs that no longer
--        exist).
--        LMI UNI signaling enables subscribers to find out
--        about the PVC status of the network, thus inhibiting
--        the use of an unavailable PVC and supplies procedures
--        for detecting and modifying following events:
--            * deletion of a PVC
--            * addition of a PVC
--            * availability of a configured PVC
--            * unavailability of a configured PVC
--            * error due to LMI message sequencing
--    
--    ELMI : Enhanced LMI
--           ELMI allows the router to learn QoS(Quality of
--           Service) parameters from the switch and use them
--           for traffic shaping, configuration or management
--           purposes. 
--    
--    CLLM : Consolidated Link Layer Management.
--        The CLLM is an out-of-band mechanism to transport
--        congestion-related information to the far end.
--        The CLLM enables the Frame Relay network to more
--        efficiently relay congestion notifications to the DTE(router).
--        The CLLM congestion notification is sent on the reserved
--        data link connection identifier(DLCI) 1023.
--    
--    Frame Forwarding Port: Frame Forwarding Ports are identified
--    by portType = frame-forward(3). The signaling parameters
--    are not applicable to these ports.
--  RevDate
--    200303240000Z
--  RevDescr
--    Added portLmiSigConfMethod mib object to support LMI 
--     Autosense feature
--  RevDate
--    200209040000Z
--  RevDescr
--    Initial version of the MIB.
--    
--    The content of this MIB was originally available
--    in CISCO-WAN-AXIPOP-MIB defined using SMIv1.
--    The applicable objects from CISCO-WAN-AXIPOP-MIB
--    are defined using SMIv2 in this MIB. Also the
--    descriptions of some of the objects have been 
--    modified.

frPortCnfSigLMIGrp OBJECT IDENTIFIER ::= { frPortCnfSig 1 }
frPortCntSigLMIGrp OBJECT IDENTIFIER ::= { frPortCntSig 1 }
frPortCnfSigCLLMGrp OBJECT IDENTIFIER ::= { frPortCnfSig 2 }
frPortCntSigCLLMGrp OBJECT IDENTIFIER ::= { frPortCntSig 2 }
cwfSignalingMIBConformance OBJECT IDENTIFIER ::= { ciscoWanFrSignalingMIB 2 }
cwfSignalingMIBGroups OBJECT IDENTIFIER ::= { cwfSignalingMIBConformance 1 }
cwfSignalingMIBCompliances OBJECT IDENTIFIER ::= { cwfSignalingMIBConformance 2 }

frPortCnfSigLMIGrpTable OBJECT-TYPE
    SYNTAX SEQUENCE OF FrPortCnfSigLMIGrpEntry
    ACCESS not-accessible
    STATUS mandatory
    DESCRIPTION
        "This table is for configuration of
        singaling(LMI) on  frame relay ports."
    ::= { frPortCnfSigLMIGrp 1 }

frPortCnfSigLMIGrpEntry OBJECT-TYPE
    SYNTAX FrPortCnfSigLMIGrpEntry
    ACCESS not-accessible
    STATUS mandatory
    DESCRIPTION
        "An entry for each frame relay port. The entries
        are applicable only for following ports:
           portType = frame-relay(1),
           portType = frFUNI(2).
        This table is not applicable for Frame Forwarding
        ports,i.e portType = frame-forward(3)."
    INDEX { lmiCnfPortNum }
    ::= { frPortCnfSigLMIGrpTable 1 }

FrPortCnfSigLMIGrpEntry ::= SEQUENCE {
    lmiCnfPortNum INTEGER,
    signallingProtocolType INTEGER,
    asynchronousUpdates INTEGER,
    t391LinkIntegrityTimer INTEGER,
    t392PollingVerificationTimer INTEGER,
    n391FullStatusPollingCounter INTEGER,
    n392ErrorThreshold INTEGER,
    n393MonitoredEventCount INTEGER,
    enhancedLmi INTEGER,
    portFRF1Dot2Support INTEGER,
    portLmiSigConfMethod INTEGER
    }

lmiCnfPortNum OBJECT-TYPE
    SYNTAX INTEGER(1..2147483647)
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "The value of this object identifies the frame
        relay port. The value of this object must be 
        same as the value of 'portNum' from frPortCnfPortGrpTable.
        
        The Frame Forwarding Port value is not valid for 
        this object."
    REFERENCE
        "portNum object in CISCO-WAN-FR-PORT-MIB.my"
    ::= { frPortCnfSigLMIGrpEntry 1 }

signallingProtocolType OBJECT-TYPE
    SYNTAX INTEGER {
        other(1),
        noSignalling(2),
        strataLMI(3),
        annexAUNI(4),
        annexDUNI(5),
        annexANNI(6),
        annexDNNI(7)
        }
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        "The value of this object is used for configuring
        the LMI signaling protocol type.
                1 - other.  Not a valid value for SET request.
                2 - noSignalling
                3 - strataLMI
                4 - annexAUNI
                5 - annexDUNI
                6 - annexANNI
                7 - annexDNNI
        
         The ports with portType = frame-forward(3)
         can be set to noSingalling(2) only.
        
         The value strataLMI(3) is not supported for 
         portHeaderLen =  fourOctets(2)."
    REFERENCE
        "ANSI T1.617 Annex D, ITU Q.933 Annex A."
    DEFVAL { noSignalling }
    ::= { frPortCnfSigLMIGrpEntry 2 }

asynchronousUpdates OBJECT-TYPE
    SYNTAX INTEGER {
        disable(1),
        enable(2),
        fsenable(3),
        updfsenable(4)
        }
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        "This object is used for configuring asynchronous
         updates.
        
         The possible values are :
        
           disable(1)     : disable Asynchronous Status Updates 
                            & Unsolicited Full Status
           enable(2)      :  enable Asynchronous Status Updates
           fsenable(3)    :  enable Unsolicited Full Status
           updfsenable(4) :  enable Asynchronous Status Updates &
                             Unsolicited Full Status."
    DEFVAL { disable }
    ::= { frPortCnfSigLMIGrpEntry 3 }

t391LinkIntegrityTimer OBJECT-TYPE
    SYNTAX INTEGER(5..30)
--  Units
--    seconds
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        "The value of this object identifies the desired
        User-side T391 link integrity verification polling
        timer value for this UNI/NNI logical port."
    DEFVAL { 10 }
    ::= { frPortCnfSigLMIGrpEntry 4 }

t392PollingVerificationTimer OBJECT-TYPE
    SYNTAX INTEGER(5..30)
--  Units
--    seconds
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        "The value of this object identifies the desired
        Network-side T392 polling verification timer value
        (nT2 for LMI) for this UNI/NNI logical port.
        This is the length of time the network should 
        wait between Status Inquiry Messages."
    DEFVAL { 15 }
    ::= { frPortCnfSigLMIGrpEntry 5 }

n391FullStatusPollingCounter OBJECT-TYPE
    SYNTAX INTEGER(1..255)
--  Units
--    Polls
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        "The value of this object identifies the
        User-Side 391 full status polling cycle value
        for this UNI/NNI logical port."
    REFERENCE
        "Q.933 Annex A [22],
        T1.617 Annex D [17]"
    DEFVAL { 6 }
    ::= { frPortCnfSigLMIGrpEntry 6 }

n392ErrorThreshold OBJECT-TYPE
    SYNTAX INTEGER(1..10)
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        "The value of this object identifies the desired
        User-side/Network-side N392 error threshold value for this
        UNI/NNI logical port."
    REFERENCE
        "Q.933 Annex A [22],
        T1.617 Annex D [17]"
    DEFVAL { 3 }
    ::= { frPortCnfSigLMIGrpEntry 7 }

n393MonitoredEventCount OBJECT-TYPE
    SYNTAX INTEGER(1..10)
--  Units
--    Events
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        "The value of this object identifies the desired
        User-side/Network-side N393 monitored events count 
        value for this UNI/NNI logical port."
    REFERENCE
        "Q.933 Annex A [22],
        T1.617 Annex D [17]"
    DEFVAL { 4 }
    ::= { frPortCnfSigLMIGrpEntry 8 }

enhancedLmi OBJECT-TYPE
    SYNTAX INTEGER {
        disable(1),
        enable(2)
        }
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        "This object enables/disables the Enhanced LMI
        (ELMI) on the frame relay port."
    DEFVAL { disable }
    ::= { frPortCnfSigLMIGrpEntry 9 }

portFRF1Dot2Support OBJECT-TYPE
    SYNTAX INTEGER {
        enable(1),
        disable(2)
        }
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        "This object enables/disables the FRF 1.2 feature.
         This object is added for FRSM12.
        
        This object is not applicable to MGX Release 1.x "
    REFERENCE
        "FRF 1.2"
    DEFVAL { disable }
    ::= { frPortCnfSigLMIGrpEntry 10 }

portLmiSigConfMethod OBJECT-TYPE
    SYNTAX INTEGER {
        manual(1),
        autosense(2)
        }
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        " 
         This object enables/disables the port LMI signalling autosense.
        
         Setting this object to autosense(2) enables the port to
         autodetect and configure port LMI signalling type.
        
         signallingProtocolType mib should be set to noSignalling 
         while this object is being set to autosense(2). If 
         signallingProtocolType mib is set to a value other than 
         noSignalling while this object is being set to autosense(2), 
         the set request fails.
        
         When this object is set to manual(1), user needs to manually
         configure the port LMI signalling type using the
         signallingProtocolType mib. signallingProtocolType can be 
         configured to any valid value including noSignalling when 
         this object is set to manual(1)."
    DEFVAL { manual }
    ::= { frPortCnfSigLMIGrpEntry 11 }

frPortCntSigLMIGrpTable OBJECT-TYPE
    SYNTAX SEQUENCE OF FrPortCntSigLMIGrpEntry
    ACCESS not-accessible
    STATUS mandatory
    DESCRIPTION
        "This table contains the LMI statistics 
        of frame relay ports."
    ::= { frPortCntSigLMIGrp 1 }

frPortCntSigLMIGrpEntry OBJECT-TYPE
    SYNTAX FrPortCntSigLMIGrpEntry
    ACCESS not-accessible
    STATUS mandatory
    DESCRIPTION
        "An entry for each frame relay port.
        Each entry identifies the LMI statistics supported
        on a frame relay port.
        The entries are applicable only for following ports:
           portType = frame-relay(1),
           portType = frFUNI(2).
        This table is not applicable for Frame Forwarding
        ports,i.e portType = frame-forward(3)."
    INDEX { lmiSigPortNum }
    ::= { frPortCntSigLMIGrpTable 1 }

FrPortCntSigLMIGrpEntry ::= SEQUENCE {
    lmiSigPortNum INTEGER,
    rcvStatusInquiry Counter,
    rcvInvalidRequest Counter,
    rcvUNISeqMismatch Counter,
    xmtStatus Counter,
    xmtAsynchUpdate Counter,
    uniSignalingTimeout Counter,
    xmtStatusInquiry Counter,
    rcvStatus Counter,
    rcvAsynchUpdate Counter,
    rcvNNISeqMismatch Counter,
    nniSignalingTimeout Counter
    }

lmiSigPortNum OBJECT-TYPE
    SYNTAX INTEGER(1..2147483647)
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "The value of this object refers to
        the frame relay port. The value for
        this object must be same as the 'portNum'
        object defined in frPortCnfPortGrpTable.
        
        The frame forwarding port value is not valid
        for this object."
    REFERENCE
        "portNum object in CISCO-WAN-FR-PORT-MIB.my"
    ::= { frPortCntSigLMIGrpEntry 1 }

rcvStatusInquiry OBJECT-TYPE
    SYNTAX Counter
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "The number of Status Inquiry messages received."
    ::= { frPortCntSigLMIGrpEntry 2 }

rcvInvalidRequest OBJECT-TYPE
    SYNTAX Counter
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "The number of Invalid Request messages received."
    ::= { frPortCntSigLMIGrpEntry 3 }

rcvUNISeqMismatch OBJECT-TYPE
    SYNTAX Counter
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "The number of times UNI messages 
        with sequence number mismatches were received."
    ::= { frPortCntSigLMIGrpEntry 4 }

xmtStatus OBJECT-TYPE
    SYNTAX Counter
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "The number of times Status response messages 
        transmitted."
    ::= { frPortCntSigLMIGrpEntry 5 }

xmtAsynchUpdate OBJECT-TYPE
    SYNTAX Counter
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "The number of times Asynch Status messages 
        transmitted."
    ::= { frPortCntSigLMIGrpEntry 6 }

uniSignalingTimeout OBJECT-TYPE
    SYNTAX Counter
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "The number of times UNI Status requests 
        were not received."
    ::= { frPortCntSigLMIGrpEntry 7 }

xmtStatusInquiry OBJECT-TYPE
    SYNTAX Counter
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "The number of Status Inquiry messages transmitted."
    ::= { frPortCntSigLMIGrpEntry 8 }

rcvStatus OBJECT-TYPE
    SYNTAX Counter
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "The number of times Status response messages received."
    ::= { frPortCntSigLMIGrpEntry 9 }

rcvAsynchUpdate OBJECT-TYPE
    SYNTAX Counter
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "The number of times Asynch Status messages received"
    ::= { frPortCntSigLMIGrpEntry 10 }

rcvNNISeqMismatch OBJECT-TYPE
    SYNTAX Counter
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "The number of times NNI messages 
        with sequence number mismatches were received."
    ::= { frPortCntSigLMIGrpEntry 11 }

nniSignalingTimeout OBJECT-TYPE
    SYNTAX Counter
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "The number of times NNI Status requests were 
        not received."
    ::= { frPortCntSigLMIGrpEntry 12 }

frPortCnfSigCLLMGrpTable OBJECT-TYPE
    SYNTAX SEQUENCE OF FrPortCnfSigCLLMGrpEntry
    ACCESS not-accessible
    STATUS mandatory
    DESCRIPTION
        "This table is configuring the CLLM on
        frame relay ports. This table is not 
        applicable for Frame Forwarding ports."
    ::= { frPortCnfSigCLLMGrp 1 }

frPortCnfSigCLLMGrpEntry OBJECT-TYPE
    SYNTAX FrPortCnfSigCLLMGrpEntry
    ACCESS not-accessible
    STATUS mandatory
    DESCRIPTION
        "An entry for each frame relay port. The entries
        are applicable only for following ports:
           portType = frame-relay(1),
           portType = frFUNI(2).
        This table is not applicable for Frame Forwarding
        ports,i.e portType = frame-forward(3)."
    INDEX { cllmCnfPortNum }
    ::= { frPortCnfSigCLLMGrpTable 1 }

FrPortCnfSigCLLMGrpEntry ::= SEQUENCE {
    cllmCnfPortNum INTEGER,
    cllmEnable INTEGER,
    xmtCLLMStatusTimer INTEGER,
    rcvCLLMStatusTimer INTEGER
    }

cllmCnfPortNum OBJECT-TYPE
    SYNTAX INTEGER(1..2147483647)
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "The value of this object identifies the frame
        relay port. The value of this object must be
        same as the value of 'portNum' from frPortCnfPortGrpTable.
        
        The Frame Forwarding Port value is not valid for 
        this object."
    REFERENCE
        "portNum object in CISCO-WAN-FR-PORT-MIB.my"
    ::= { frPortCnfSigCLLMGrpEntry 1 }

cllmEnable OBJECT-TYPE
    SYNTAX INTEGER {
        disable(1),
        enable(2)
        }
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        "This object is used for enabling/disabling
        CLLM on frame relay port.
        When set to 'disabled', CLLM is disabled.
        When set to 'enabled', CLLM is enabled."
    DEFVAL { disable }
    ::= { frPortCnfSigCLLMGrpEntry 2 }

xmtCLLMStatusTimer OBJECT-TYPE
    SYNTAX INTEGER(40..5000)
--  Units
--    milli-seconds
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        "Interval in milliseconds for CLLM to send CLLM updates."
    DEFVAL { 40 }
    ::= { frPortCnfSigCLLMGrpEntry 3 }

rcvCLLMStatusTimer OBJECT-TYPE
    SYNTAX INTEGER {
        rcvCLLMTimerValue(1000)
        }
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "Timeout value for receiving CLLM updates."
    DEFVAL { rcvCLLMTimerValue }
    ::= { frPortCnfSigCLLMGrpEntry 4 }

frPortCntSigCLLMGrpTable OBJECT-TYPE
    SYNTAX SEQUENCE OF FrPortCntSigCLLMGrpEntry
    ACCESS not-accessible
    STATUS mandatory
    DESCRIPTION
        "This table is for CLLM statistics for
        frame relay ports."
    ::= { frPortCntSigCLLMGrp 1 }

frPortCntSigCLLMGrpEntry OBJECT-TYPE
    SYNTAX FrPortCntSigCLLMGrpEntry
    ACCESS not-accessible
    STATUS mandatory
    DESCRIPTION
        " An entry for frame relay port.
        The entries are applicable only for following ports:
           portType = frame-relay(1),
           portType = frFUNI(2).
        This table is not applicable for Frame Forwarding
        ports,i.e portType = frame-forward(3)."
    INDEX { cllmSigPortNum }
    ::= { frPortCntSigCLLMGrpTable 1 }

FrPortCntSigCLLMGrpEntry ::= SEQUENCE {
    cllmSigPortNum INTEGER,
    rcvFramesCLLM Counter,
    rcvBytesCLLM Counter,
    xmtFramesCLLM Counter,
    xmtBytesCLLM Counter,
    cllmFailures Counter
    }

cllmSigPortNum OBJECT-TYPE
    SYNTAX INTEGER(1..2147483647)
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "The value of this object identifies the frame
        relay port. The value of this object must be
        same as the value of 'portNum' from frPortCnfPortGrpTable.
        
        The Frame Forwarding Port value is not valid for 
        this object."
    REFERENCE
        "portNum object in CISCO-WAN-FR-PORT-MIB.my"
    ::= { frPortCntSigCLLMGrpEntry 1 }

rcvFramesCLLM OBJECT-TYPE
    SYNTAX Counter
--  Units
--    frames
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "The number of CLLM frames received."
    ::= { frPortCntSigCLLMGrpEntry 2 }

rcvBytesCLLM OBJECT-TYPE
    SYNTAX Counter
--  Units
--    bytes
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "The number of CLLM bytes received."
    ::= { frPortCntSigCLLMGrpEntry 3 }

xmtFramesCLLM OBJECT-TYPE
    SYNTAX Counter
--  Units
--    frames
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "The number of CLLM frames transmitted."
    ::= { frPortCntSigCLLMGrpEntry 4 }

xmtBytesCLLM OBJECT-TYPE
    SYNTAX Counter
--  Units
--    bytes
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "The number of CLLM bytes transmitted."
    ::= { frPortCntSigCLLMGrpEntry 5 }

cllmFailures OBJECT-TYPE
    SYNTAX Counter
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "The number of times an expected CLLM
        message was not received."
    ::= { frPortCntSigCLLMGrpEntry 6 }

ciscoWanFrLmiConfigGroup OBJECT IDENTIFIER ::= { cwfSignalingMIBGroups 1 }
-- OBJECT-GROUP
--  Status
--    mandatory
--  Descr
--    A collection of objects providing information
--    applicable to Frame Relay Logical Ports
--    (Frame Relay Ports).
--  objects
--    lmiCnfPortNum, signallingProtocolType, asynchronousUpdates, 
--    t391LinkIntegrityTimer, t392PollingVerificationTimer, 
--    n391FullStatusPollingCounter, n392ErrorThreshold, 
--    n393MonitoredEventCount, enhancedLmi, portFRF1Dot2Support, 
--    portLmiSigConfMethod

ciscoWanFrLmiStatsGroup OBJECT IDENTIFIER ::= { cwfSignalingMIBGroups 2 }
-- OBJECT-GROUP
--  Status
--    mandatory
--  Descr
--    A collection of objects providing information
--    applicable to LMI statistics on Frame Relay Ports.
--  objects
--    lmiSigPortNum, rcvStatusInquiry, rcvInvalidRequest, 
--    rcvUNISeqMismatch, xmtStatus, xmtAsynchUpdate, 
--    uniSignalingTimeout, xmtStatusInquiry, rcvStatus, 
--    rcvAsynchUpdate, rcvNNISeqMismatch, nniSignalingTimeout

ciscoWanFrCllmGroup OBJECT IDENTIFIER ::= { cwfSignalingMIBGroups 3 }
-- OBJECT-GROUP
--  Status
--    mandatory
--  Descr
--    A collection of objects providing information
--     on CLLM applicable to Frame Relay Ports.
--  objects
--    cllmCnfPortNum, cllmEnable, xmtCLLMStatusTimer, 
--    rcvCLLMStatusTimer

ciscoWanFrCllmStatsGroup OBJECT IDENTIFIER ::= { cwfSignalingMIBGroups 4 }
-- OBJECT-GROUP
--  Status
--    mandatory
--  Descr
--    A collection of objects providing information
--    applicable to CLLMI statistics on Frame Relay Ports.
--  objects
--    cllmSigPortNum, rcvFramesCLLM, rcvBytesCLLM, xmtFramesCLLM, 
--    xmtBytesCLLM, cllmFailures

cwfSignalingMIBCompliance OBJECT IDENTIFIER ::= { cwfSignalingMIBCompliances 1 }
-- MODULE-COMPLIANCE
--  Status
--    mandatory
--  Descr
--    The compliance statement for SNMP entities which have
--    network interfaces.
--  Module
--    >>current<<
--   MandGroup
--    ciscoWanFrLmiConfigGroup
--   MandGroup
--    ciscoWanFrLmiStatsGroup
--   MandGroup
--    ciscoWanFrCllmGroup
--   MandGroup
--    ciscoWanFrCllmStatsGroup


END