CISCO-IP-URPF-MIB-V1SMI.my

-- MIB file created 18-Jan-2012 17:55:31, by
--   SMICng version 2.2.11-beta(PRO)(Solaris), January 20, 2001. Enterprise key cisco.com

CISCO-IP-URPF-MIB DEFINITIONS ::= BEGIN

-- From file: "CISCO-IP-URPF-MIB.my"
-- Compile options "4 7 F H N W 03 06 0B 0G 0N 0T"

IMPORTS
    TimeStamp, TruthValue
            FROM SNMPv2-TC-v1
    SnmpAdminString
            FROM SNMP-FRAMEWORK-MIB
    ifIndex
            FROM IF-MIB
    ciscoMgmt
            FROM CISCO-SMI
    Counter, Gauge
            FROM RFC1155-SMI
    OBJECT-TYPE
            FROM RFC-1212
    TRAP-TYPE
            FROM RFC-1215;

ciscoIpUrpfMIB OBJECT IDENTIFIER ::= { ciscoMgmt 451 }
-- MODULE-IDENTITY
--  LastUpdated
--    201112290000Z
--  OrgName
--    Cisco System, Inc.
--  ContactInfo
--    Postal: Cisco Systems, Inc.
--    170 West Tasman Drive
--    San Jose, CA 95134-1706
--    USA
--    
--    Tel: +1 800 553-NETS
--    
--    E-mail: cs-cef@cisco.com
--  Descr
--    Unicast Reverse Path Forwarding (URPF) is a function that
--    checks the validity of the source address of IP packets
--    received on an interface. This in an attempt to prevent
--    Denial of Service attacks based on IP address spoofing.
--    
--    URPF checks validity of a source address by determining
--    whether the packet would be successfully routed as a
--    destination address. 
--    Based on configuration, the check made
--    can be for existence of any route for the address, or more
--    strictly for a route out the interface on which the packet
--    was received by the device. When a violating packet is
--    detected, it can be dropped. 
--    This MIB allows detection of
--    spoofingevents.
--  RevDate
--    201112290000Z
--  RevDescr
--    2 New TC are defined to support Dynamic template MIB
--  RevDate
--    200411120000Z
--  RevDescr
--    Initial version of this MIB module.

ciscoIpUrpfMIBNotifs OBJECT IDENTIFIER ::= { ciscoIpUrpfMIB 0 }
ciscoIpUrpfMIBObjects OBJECT IDENTIFIER ::= { ciscoIpUrpfMIB 1 }
ciscoIpUrpfMIBConformance OBJECT IDENTIFIER ::= { ciscoIpUrpfMIB 2 }
cipUrpfScalar   OBJECT IDENTIFIER ::= { ciscoIpUrpfMIBObjects 1 }
cipUrpfStatistics OBJECT IDENTIFIER ::= { ciscoIpUrpfMIBObjects 2 }
cipUrpfInterfaceConfig OBJECT IDENTIFIER ::= { ciscoIpUrpfMIBObjects 3 }
cipUrpfVrf      OBJECT IDENTIFIER ::= { ciscoIpUrpfMIBObjects 4 }
ciscoIpUrpfMIBCompliances OBJECT IDENTIFIER ::= { ciscoIpUrpfMIBConformance 1 }
ciscoIpUrpfMIBGroups OBJECT IDENTIFIER ::= { ciscoIpUrpfMIBConformance 2 }

UnicastRpfType ::= INTEGER {
        strict(1),
        loose(2),
        disabled(3)
        }
-- TEXTUAL-CONVENTION
--  Status
--    mandatory
--  Descr
--    An enumerated integer-value describing the type of
--    unicast Reverse Path Forwarding (RPF) a system applies to
--    traffic received on an interface. UnicastRpfTypes 'strict' and 
--    'loose' RPF methods are defined in RFC3704.
--    
--    'disabled'
--        The system does not perform unicast RPF on packets received
--        by the interface.
--    
--    'strict'
--        The system performs strict unicast RPF on packets received
--        by the interface.
--    'loose'
--        The system performs loose unicast RPF on packets received by
--        the interface.
--  Refer
--    RFC3704 (http://tools.ietf.org/html/rfc3704)

UnicastRpfOptions ::= OCTET STRING(SIZE(1..2))
        -- BITS are:
        --   allowDefault(0)
        --   allowSelfPing(1)
-- TEXTUAL-CONVENTION
--  Status
--    mandatory
--  Descr
--    A bit string describing unicast Reverse Path Forwarding (RPF)
--    options:
--    
--    'allowDefault'
--        Allows the use of the default route for RPF verification.
--    
--    'allowSelfPing'
--        Allows a router to ping its own interface or interfaces.

cipUrpfDropRateWindow OBJECT-TYPE
    SYNTAX INTEGER(1..600)
--  Units
--    seconds
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        "The window of time in the recent past over which the drop
        count used in the drop rate computation is collected. 
        This global value applies for the computation of all URPF 
        rates, global and per-interface. 
        
        Once the period over which computations have been 
        performed exceeds cipUrpfDropRateWindow, every time a 
        computation is performed, the window slides up to end 
        at the current time and start at cipUrpfDropRateWindow 
        seconds before. 
        
        The cipUrpfDropRateWindow must be greater than
        or equal to the interval between computations 
        (cipUrpfComputeInterval).
        
        Since the agent must save the drop count values
        for each compute interval in order to slide the window,
        the number of counts saved is the quotient of
        cipUrpfDropRateWindow divided by cipUrpfComputeInterval."
    DEFVAL { 300 }
    ::= { cipUrpfScalar 1 }

cipUrpfComputeInterval OBJECT-TYPE
    SYNTAX INTEGER(1..120)
--  Units
--    seconds
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        "The time between rate computations. This global value
        applies for the computation of all URPF rates, global
        and per-interface.
        
        When the value of cipUrpfComputeInterval is changed,
        the interval in-progress proceeds as though the value
        had not changed. The change will apply to the length
        of subsequent intervals.
        
        The cipUrpfComputeInterval must be less than or equal 
        to the cipUrpfDropRateWindow."
    DEFVAL { 30 }
    ::= { cipUrpfScalar 2 }

cipUrpfDropNotifyHoldDownTime OBJECT-TYPE
    SYNTAX INTEGER(1..1000)
--  Units
--    seconds
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        "The minimum time between issuance of
        cipUrpfIfDropRateNotify notifications for a 
        particular interface and packet forwarding type.
        
        Notifications are generated for each interface and
        packet forwarding type that exceeds the drop-rate. 
        When a Notify is sent because the drop-rate is 
        exceeded for a particular interface and forwarding
        type, the time specified by this object is used to 
        specify the minimum time that must elapse before 
        another Notify can be sent for that interface and
        forwarding type. The time is specified globally but 
        used individually."
    DEFVAL { 300 }
    ::= { cipUrpfScalar 3 }

cipUrpfTable OBJECT-TYPE
    SYNTAX SEQUENCE OF CipUrpfEntry
    ACCESS not-accessible
    STATUS mandatory
    DESCRIPTION
        "This table contains summary information for the
        managed device on URPF dropping."
    ::= { cipUrpfStatistics 1 }

cipUrpfEntry OBJECT-TYPE
    SYNTAX CipUrpfEntry
    ACCESS not-accessible
    STATUS mandatory
    DESCRIPTION
        "If the managed device supports URPF dropping,
        a row exists for each IP version type (v4 and v6).
        A row contains summary information on URPF
        dropping over the entire managed device."
    INDEX { cipUrpfIpVersion }
    ::= { cipUrpfTable 1 }

CipUrpfEntry ::= SEQUENCE {
    cipUrpfIpVersion INTEGER,
    cipUrpfDrops Counter,
    cipUrpfDropRate Gauge
    }

cipUrpfIpVersion OBJECT-TYPE
    SYNTAX INTEGER {
        ipv4(1),
        ipv6(2)
        }
    ACCESS not-accessible
    STATUS mandatory
    DESCRIPTION
        "Specifies the version of IP forwarding on an interface
        to which the table row URPF counts, rates, and
        configuration apply."
    ::= { cipUrpfEntry 1 }

cipUrpfDrops OBJECT-TYPE
    SYNTAX Counter
--  Units
--    packets
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "Sum of dropped IP version cipUrpfIpVersion packets failing
        a URPF check. This value is the sum of drops of packets 
        received on all interfaces of the managed device."
    ::= { cipUrpfEntry 2 }

cipUrpfDropRate OBJECT-TYPE
    SYNTAX Gauge
--  Units
--    packets per second
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "The rate of packet drops of IP version cipUrpfIpVersion
        packets due to URPF for the managed device. The
        per-interface drop rate notification is issued on rates
        exceeding a limit (rising rate). This dropping may indicate
        an security attack on the network. To determine whether the
        attack/event is over, the NMS must consult the managed
        device. This object can be polled to determine the recent
        drop rate for the managed device as a whole, in addition to
        querying particular interface objects. 
        This object is the
        average rate of dropping over the most recent window of
        time. The rate is computed by dividing the number of packets
        dropped over a window by the window time in seconds. The
        window time is specified by cipUrpfDropRateWindow. Each time
        the drop rate is computed, and at system startup, a snapshot
        is taken of the latest value of cipUrpfDrops. Subtracting
        from this the snapshot of cipUrpfDrops at the start of the
        current window of time gives the number of packets dropped.
        The drop rate is computed every cipUrpfComputeInterval
        seconds. As an example, let cipUrpfDropRateWindow be 300
        seconds, and cipUrpfComputeInterval 30 seconds. Every 30
        seconds, the drop count five minutes previous is subtracted
        from the current drop count, and the result is divided by
        300 to arrive at the drop rate. 
        At device start-up, until
        the device has been up more than cipUrpfDropRateWindow, when
        drop rate is computed, the value of cipUrpfDrops is divided
        by the time the device has been up. 
        After the device has
        been up for cipUrpfDropRateWindow, when drop rate is
        computed, the number of packet drops counted from interval
        start time to the computation time is divided by
        cipUrpfDropRateWindow. 
        Changes to cipUrpfDropRateWindow are
        not reflected in this object until the next computation
        time. 
        The rate from the most recent computation is the
        value fetched until the subsequent computation is
        performed."
    ::= { cipUrpfEntry 3 }

cipUrpfIfMonTable OBJECT-TYPE
    SYNTAX SEQUENCE OF CipUrpfIfMonEntry
    ACCESS not-accessible
    STATUS mandatory
    DESCRIPTION
        "This table contains information on URPF dropping on
        an interface."
    ::= { cipUrpfStatistics 2 }

cipUrpfIfMonEntry OBJECT-TYPE
    SYNTAX CipUrpfIfMonEntry
    ACCESS not-accessible
    STATUS mandatory
    DESCRIPTION
        "If IPv4 packet forwarding is configured on an interface,
        and is configured to perform URPF checking, a row appears
        in this table with indices [ifIndex][ipv4]. If IPv4
        packet forwarding is deconfigured, or URPF checking
        is deconfigured, the row disappears.
        
        If IPv6 packet forwarding is configured on an interface,
        and is configured to perform URPF checking, a row appears
        in the table with indices [ifIndex][ipv6].  If IPv6
        packet forwarding is deconfigured, or URPF checking
        is deconfigured, the row disappears."
    INDEX { ifIndex, cipUrpfIfIpVersion }
    ::= { cipUrpfIfMonTable 1 }

CipUrpfIfMonEntry ::= SEQUENCE {
    cipUrpfIfIpVersion INTEGER,
    cipUrpfIfDrops Counter,
    cipUrpfIfSuppressedDrops Counter,
    cipUrpfIfDropRate Gauge,
    cipUrpfIfDiscontinuityTime TimeStamp
    }

cipUrpfIfIpVersion OBJECT-TYPE
    SYNTAX INTEGER {
        ipv4(1),
        ipv6(2)
        }
    ACCESS not-accessible
    STATUS mandatory
    DESCRIPTION
        "Specifies the version of IP forwarding on an interface
        to which the table row URPF counts, rates, and 
        configuration apply."
    ::= { cipUrpfIfMonEntry 1 }

cipUrpfIfDrops OBJECT-TYPE
    SYNTAX Counter
--  Units
--    packets
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "The number of IP packets of version cipUrpfIfIpVersion
        failing the URPF check and dropped by the managed device
        on a particular interface.
        
        Discontinuities in the value of this variable can occur 
        at re-initialization of the management system, and at 
        other times as indicated by the values of 
        cipUrpfIfDiscontinuityTime."
    ::= { cipUrpfIfMonEntry 2 }

cipUrpfIfSuppressedDrops OBJECT-TYPE
    SYNTAX Counter
--  Units
--    packets
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "The number of IP packets of version cipUrpfIfIpVersion
        failing the URPF check but given a reprieve and not 
        dropped by the managed device. Depending on the 
        device configuration and capabilities, the following 
        cases may cause incrementing of the counter: 
        - if the managed device is configured to allow self-pings 
          and the managed device pings itself.
        - if the managed device is configured for loose URPF (if any
          interface has a route to the source), and the strict
          case fails while the loose case passes.
        - DHCP Request packets (src 0.0.0.0 dst 255.255.255.255) 
          will pass after initially being marked for drop.
        - RIP routing on unnumbered interfaces will pass after 
          initially being marked for drop.
        - multicast packets will pass after initially being marked 
          for drop
        - ACL's can be applied to permit packets after initially 
          being marked for drop.
        
        Discontinuities in the value of this variable can occur 
        at re-initialization of the management system, and at 
        other times as indicated by the values of 
        cipUrpfIfDiscontinuityTime."
    ::= { cipUrpfIfMonEntry 3 }

cipUrpfIfDropRate OBJECT-TYPE
    SYNTAX Gauge
--  Units
--    packets/second
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "The rate of packet drops of IP version cipUrpfIfIpVersion
        packets due to URPF on the interface. 
        
        This object is the average rate of dropping over the most 
        recent interval of time. The rate is computed by dividing
        the number of packets dropped over an interval by the 
        interval time in seconds. Each time the drop rate
        is computed, and at system startup, a snapshot is taken
        of the latest value of cipUrpfIfDrops. Subtracting from this
        the snapshot of cipUrpfIfDrops at the start of the current
        interval of time gives the number of packets dropped.
        The drop rate is computed every cipUrpfComputeInterval
        seconds.
        
        When drop rate is computed, if time since the creation of 
        a row in cipUrpfIfMonTable is less than 
        cipUrpfDropRateWindow, the value of cipUrpfIfDrops is 
        divided by the time since row was created.
        
        After the row has been in existence for 
        cipUrpfDropRateWindow, when drop rate is computed, the 
        number of packet drops counted on the interface from 
        interval start time to the computation time is divided 
        by cipUrpfDropRateWindow.
        
        Changes to cipUrpfDropRateWindow are not reflected in this
        object until the next computation time.
        
        The rate from the  most recent computation is the value 
        fetched until the subsequent computation is performed."
    ::= { cipUrpfIfMonEntry 4 }

cipUrpfIfDiscontinuityTime OBJECT-TYPE
    SYNTAX TimeStamp
--    Rsyntax TimeTicks
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "The value of sysUpTime on the most recent
        occasion at which this interface's  counters
        suffered  a discontinuity.
        If no such discontinuities have occurred
        since the last re-initialization of the
        local management subsystem, then this
        object contains a value of zero."
    ::= { cipUrpfIfMonEntry 5 }

cipUrpfIfConfTable OBJECT-TYPE
    SYNTAX SEQUENCE OF CipUrpfIfConfEntry
    ACCESS not-accessible
    STATUS mandatory
    DESCRIPTION
        "This table contains statistics information on URPF on
        an interface."
    ::= { cipUrpfInterfaceConfig 1 }

cipUrpfIfConfEntry OBJECT-TYPE
    SYNTAX CipUrpfIfConfEntry
    ACCESS not-accessible
    STATUS mandatory
    DESCRIPTION
        "A row exists in this table if a row exists
        in cipUrpfIfMonTable."
    INDEX { ifIndex, cipUrpfIfIpVersion }
-- Augments cipUrpfIfMonEntry
    ::= { cipUrpfIfConfTable 1 }

CipUrpfIfConfEntry ::= SEQUENCE {
    cipUrpfIfDropRateNotifyEnable TruthValue,
    cipUrpfIfNotifyDropRateThreshold Gauge,
    cipUrpfIfNotifyDrHoldDownReset TruthValue,
    cipUrpfIfCheckStrict INTEGER,
    cipUrpfIfWhichRouteTableID INTEGER,
    cipUrpfIfVrfName SnmpAdminString
    }

cipUrpfIfDropRateNotifyEnable OBJECT-TYPE
    SYNTAX TruthValue
--    Rsyntax INTEGER {
--        true(1),
--        false(2)
--        }
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        "This object specifies whether the system produces the
        cipUrpfIfDropRateNotify notification as a result of URPF 
        dropping of version cipUrpfIfIpVersion IP packets on this 
        interface. A false value prevents such notifications from 
        being generated by this system."
    DEFVAL { false }
    ::= { cipUrpfIfConfEntry 1 }

cipUrpfIfNotifyDropRateThreshold OBJECT-TYPE
    SYNTAX Gauge
--  Units
--    packets/second
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        "When the calculated rate of URPF packet drops
        (cipUrpfIfDropRate) meets or exceeds the value 
        specified by this object, a cipUrpfIfDropRateNotify 
        notification is sent if cipUrpfIfDropRateNotifyEnable 
        is set to true, and no such notification for the
        IP version has been sent for this interface for the 
        hold-down period.
        
        Note that due to the calculation used for drop rate, 
        if there are less than n drop events in an n-second
        period the notification will not be generated. To allow
        for the detection of a small number of drop events, the
        value 0 (zero) is used to indicate that if any drop events
        occur during the interval, a notification is generated."
    DEFVAL { 1000 }
    ::= { cipUrpfIfConfEntry 2 }

cipUrpfIfNotifyDrHoldDownReset OBJECT-TYPE
    SYNTAX TruthValue
--    Rsyntax INTEGER {
--        true(1),
--        false(2)
--        }
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        "Setting this object to true causes the five-minute
        hold-down timer for emitting URPF drop rate 
        notifications for IP version cipUrpfIfIpVersion on 
        the interface to be short-circuited.  If a notification 
        is due and would be emitted for the interface if the 
        five-minutes elapsed, setting this object will cause 
        the notification to be sent.
        
        This is a trigger, and doesn't hold information. It is
        set and an action is performed. Therefore a get for 
        this object always returns false."
    DEFVAL { false }
    ::= { cipUrpfIfConfEntry 3 }

cipUrpfIfCheckStrict OBJECT-TYPE
    SYNTAX INTEGER {
        strict(1),
        loose(2)
        }
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "Interface configuration indicating the strictness of
        the reachability check performed 
        on the interface.
        - strict: check that source addr is reachable via 
                  the interface it came in on.
        - loose : check that source addr is reachable via 
                  some interface on the device."
    ::= { cipUrpfIfConfEntry 4 }

cipUrpfIfWhichRouteTableID OBJECT-TYPE
    SYNTAX INTEGER {
        default(1),
        vrf(2)
        }
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "Interface configuration indicating the routing table
        consulted for the reachability check:
        - default: the non-private routing table for of the 
                   managed system.
        - vrf   : a particular VPN routing table."
    ::= { cipUrpfIfConfEntry 5 }

cipUrpfIfVrfName OBJECT-TYPE
    SYNTAX SnmpAdminString(SIZE(0..32))
--    Rsyntax OCTET STRING(SIZE(0..32))
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "If the value of cipUrpfIfWhichRouteTableID is 'vrf',
        the name of the VRF Table. Otherwise a zero-length
        string."
    ::= { cipUrpfIfConfEntry 6 }

cipUrpfVrfTable OBJECT-TYPE
    SYNTAX SEQUENCE OF CipUrpfVrfEntry
    ACCESS not-accessible
    STATUS mandatory
    DESCRIPTION
        "This table enables indexing URPF drop statistics
        by Virtual Routing and Forwarding instances."
    ::= { cipUrpfVrf 1 }

cipUrpfVrfEntry OBJECT-TYPE
    SYNTAX CipUrpfVrfEntry
    ACCESS not-accessible
    STATUS mandatory
    DESCRIPTION
        "An entry exists for a VRF if and only if the VRF
        is associated with an interface that is configured
        to perform IP URPF checking using the routing table 
        for that VRF."
    INDEX { cipUrpfVrfName }
    ::= { cipUrpfVrfTable 1 }

CipUrpfVrfEntry ::= SEQUENCE {
    cipUrpfVrfName SnmpAdminString
    }

cipUrpfVrfName OBJECT-TYPE
    SYNTAX SnmpAdminString(SIZE(0..32))
--    Rsyntax OCTET STRING(SIZE(0..32))
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "This field is used to specify the VRF Table
        name."
    ::= { cipUrpfVrfEntry 1 }

cipUrpfVrfIfTable OBJECT-TYPE
    SYNTAX SEQUENCE OF CipUrpfVrfIfEntry
    ACCESS not-accessible
    STATUS mandatory
    DESCRIPTION
        "This table contains statistics information for interfaces
        performing URPF using VRF table to determine reachability."
    ::= { cipUrpfStatistics 3 }

cipUrpfVrfIfEntry OBJECT-TYPE
    SYNTAX CipUrpfVrfIfEntry
    ACCESS not-accessible
    STATUS mandatory
    DESCRIPTION
        "An entry exists for a VRF and interface if and only
        if the VRF associated with the interface is configured 
        to perform IP URPF checking using the routing 
        table for the VRF."
    INDEX { cipUrpfVrfName, ifIndex }
    ::= { cipUrpfVrfIfTable 1 }

CipUrpfVrfIfEntry ::= SEQUENCE {
    cipUrpfVrfIfDrops Counter,
    cipUrpfVrfIfDiscontinuityTime TimeStamp
    }

cipUrpfVrfIfDrops OBJECT-TYPE
    SYNTAX Counter
--  Units
--    packets
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "The number of packets failing the URPF check for a VRF on
        the interface and dropped by the managed device.
        
        Discontinuities in the value of this variable can occur 
        at re-initialization of the management system, and at 
        other times as indicated by the values of 
        cipUrpfVrfIfDiscontinuityTime."
    ::= { cipUrpfVrfIfEntry 2 }

cipUrpfVrfIfDiscontinuityTime OBJECT-TYPE
    SYNTAX TimeStamp
--    Rsyntax TimeTicks
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "The value of sysUpTime on the most recent occasion at
        which the URPF counters for this VRF on this interface 
        suffered  a discontinuity.  If no such discontinuities 
        have occurred since the last re-initialization of the
        local management subsystem, then this object contains a 
        value of zero."
    ::= { cipUrpfVrfIfEntry 3 }

cipUrpfIfDropRateNotify TRAP-TYPE
-- Reverse mappable trap
    ENTERPRISE ciscoIpUrpfMIB
    VARIABLES {
        cipUrpfIfDropRate }
--  Status
--    mandatory
    DESCRIPTION
        "This notification is generated when
        cipUrpfIfDropRateNotifyEnable is set to true and
        the calculated URPF drop rate (cipUrpfIfDropRate) 
        exceeds the notification threshold drop rate 
        (cipUrpfIfNotifyDropRateThreshold). Note the 
        exceptional value of 0 for threshold allows notification 
        generation if any drop events occur in an interval.
        
        After generating this notification, another such
        notification will not be sent out for a minimum of five 
        minutes (note the exception to this provided by 
        cipUrpfIfNotifyDrHoldDownReset).
        
        The object value present in the notification is the 
        the drop rate that exceeded the threshold."
    ::= 1

ciscoIpUrpfMIBMainObjectGroup OBJECT IDENTIFIER ::= { ciscoIpUrpfMIBGroups 1 }
-- OBJECT-GROUP
--  Status
--    mandatory
--  Descr
--    The collection of common counter objects, those
--    needed by other objects, and the common interface 
--    table.
--  objects
--    cipUrpfDropRateWindow, cipUrpfComputeInterval, 
--    cipUrpfDropNotifyHoldDownTime, cipUrpfDrops, cipUrpfDropRate, 
--    cipUrpfIfDrops, cipUrpfIfSuppressedDrops, cipUrpfIfDropRate, 
--    cipUrpfIfDropRateNotifyEnable, 
--    cipUrpfIfNotifyDropRateThreshold, 
--    cipUrpfIfNotifyDrHoldDownReset, cipUrpfIfCheckStrict, 
--    cipUrpfIfDiscontinuityTime

ciscoIpUrpfMIBVrfObjectGroup OBJECT IDENTIFIER ::= { ciscoIpUrpfMIBGroups 2 }
-- OBJECT-GROUP
--  Status
--    mandatory
--  Descr
--    The collection of objects needed to index by
--    VRF.
--  objects
--    cipUrpfVrfName, cipUrpfIfWhichRouteTableID, cipUrpfIfVrfName, 
--    cipUrpfVrfIfDrops, cipUrpfVrfIfDiscontinuityTime

ciscoIpUrpfMIBNotifyGroup OBJECT IDENTIFIER ::= { ciscoIpUrpfMIBGroups 6 }
-- NOTIFICATION-GROUP
--  Status
--    mandatory
--  Descr
--    The collection of objects which are used to specify
--    notifications for URPF.
--  notifications
--    cipUrpfIfDropRateNotify

ciscoIpUrpfMIBCompliance OBJECT IDENTIFIER ::= { ciscoIpUrpfMIBCompliances 1 }
-- MODULE-COMPLIANCE
--  Status
--    mandatory
--  Descr
--    An SNMP entity can implement this module to
--    provide URPF problem diagnosis information.
--  Module
--    >>current<<
--   MandGroup
--    ciscoIpUrpfMIBMainObjectGroup
--   MandGroup
--    ciscoIpUrpfMIBNotifyGroup
--   OptGroup
--    ciscoIpUrpfMIBVrfObjectGroup


END