CISCO-BUS-MIB-V1SMI.my

-- MIB created 6/25/99 12:56:55, by
--   SMIC (the next generation) version 1.6.29, November 22, 1994.

CISCO-BUS-MIB DEFINITIONS ::= BEGIN

-- From file: "CISCO-BUS-MIB.my"

IMPORTS
    ciscoMgmt
            FROM CISCO-SMI
    AtmLaneAddress
            FROM LAN-EMULATION-CLIENT-MIB
    Counter32, Integer32
            FROM SNMPv2-SMI-v1
    OBJECT-TYPE
            FROM RFC-1212
    RowStatus, DisplayString, TimeStamp
            FROM SNMPv2-TC-v1;

ciscoBusMIB OBJECT IDENTIFIER ::= { ciscoMgmt 40 }
-- MODULE-IDENTITY
--  LastUpdated
--    9509151702Z
--  OrgName
--    Cisco Systems Inc.
--  ContactInfo
--     Cisco Systems Inc.
--  Descr
--     The MIB module for the management of LANE broadcast and 
--    unknown servers.

ciscoBusMIBObjects OBJECT IDENTIFIER ::= { ciscoBusMIB 1 }
ciscoBusMIBConformance OBJECT IDENTIFIER ::= { ciscoBusMIB 2 }
ciscoBusMIBGroups OBJECT IDENTIFIER ::= { ciscoBusMIBConformance 1 }
ciscoBusMIBCompliances OBJECT IDENTIFIER ::= { ciscoBusMIBConformance 2 }

CiscoVpiInteger ::= INTEGER(-1..255)
-- TEXTUAL-CONVENTION
--  Status
--    mandatory
--  Descr
--     An integer large enough to hold a VPI.  In the event
--    that VC does not  exist, the value  of an  object with
--    this syntax shall be -1.

CiscoVciInteger ::= INTEGER(-1..65535)
-- TEXTUAL-CONVENTION
--  Status
--    mandatory
--  Descr
--     An integer large enough to hold a VCI.  In the event
--    that  VC does not exist, the   value on an object with
--    this syntax shall be -1.

busTable OBJECT-TYPE
    SYNTAX SEQUENCE OF BusEntry
    ACCESS not-accessible
    STATUS mandatory
    DESCRIPTION
        " A (conceptual) table representing all the instantiations
        of BUSs on the designated device.  This table may or may not
        allow the creation of rows depending on whether the LANE
        service elements allow the separate creation of LES and BUS
        components.  In the event that separate components are not
        allowed then the MINIMUM-ACCESS detailed in the 
        MODULE-COMPLIANCE should be used by those BUS implementations"
    ::= { ciscoBusMIBObjects 1 }

busEntry OBJECT-TYPE
    SYNTAX BusEntry
    ACCESS not-accessible
    STATUS mandatory
    DESCRIPTION
        " An entry (conceptual row) in the busTable."
    INDEX { busElanName, busIndex }
    ::= { busTable 1 }

BusEntry ::= SEQUENCE {
    busElanName DisplayString,
    busIndex INTEGER,
    busAtmAddrSpec AtmLaneAddress,
    busAtmAddrMask OCTET STRING,
    busAtmAddrActl AtmLaneAddress,
    busIfIndex Integer32,
    busSubIfNum Integer32,
    busUpTime TimeStamp,
    busLanType INTEGER,
    busMaxFrm INTEGER,
    busMaxFrmAge INTEGER,
    busOutFwdOctets Counter32,
    busOutFwdUcastFrms Counter32,
    busOutFwdNUcastFrms Counter32,
    busFrmTimeOuts Counter32,
    busMultiFwdVpi CiscoVpiInteger,
    busMultiFwdVci CiscoVciInteger,
    busOperStatus INTEGER,
    busAdminStatus INTEGER,
    busStatus RowStatus
    }

busElanName OBJECT-TYPE
    SYNTAX DisplayString(SIZE(1..32))
--    Rsyntax OCTET STRING(SIZE(1..32))
    ACCESS not-accessible
    STATUS mandatory
    DESCRIPTION
        " The ELAN name of the designated bridge."
    ::= { busEntry 1 }

busIndex OBJECT-TYPE
    SYNTAX INTEGER(1..2147483647)
    ACCESS not-accessible
    STATUS mandatory
    DESCRIPTION
        " A unique identifier  for this particular BUS on this
        ELAN. This value must remain  constant while the entry
        is in existence and during the  operation of the agent
        (i.e.   It is allowed to change  after  reboot).  For 
        implementations that do not support  more than one BUS
        entity per ELAN per device, it is sufficient to always
        report 1 for this object and  only to accept the value
        1 for row creation."
    ::= { busEntry 2 }

busAtmAddrSpec OBJECT-TYPE
    SYNTAX AtmLaneAddress
--    Rsyntax OCTET STRING(SIZE(0..20))
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        " The specified ATM address of the BUS on the interface
        of interest.  Note  that setting this object will have
        the side effect   of   reinitializing  the  BUS    and
        consequently dropping all clients connected to it.  If
        this object is not specified at row creation time then
        the BUS will choose a value  for itself and attempt to
        register  with the  switch  with  that  value.  If  an
        address is  specified  which is not acceptable  to the
        switch   then the busOperStatus  will remain  inactive
        until an acceptable address is set."
    ::= { busEntry 3 }

busAtmAddrMask OBJECT-TYPE
    SYNTAX OCTET STRING(SIZE(0..20))
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        "   An    address mask  that     when  used  with  the
        busAtmAddrSpec, specifies  the portion of the BUS' ATM
        address  that is desired  to be  configured. Note that
        setting    this     object   will   result   in    the
        reinitialization of the BUS, consequently dropping all
        clients connected to  it.   At row creation  time this
        object  cannot be set  without also  supplying a value
        for  the busAtmAddrSpec.  If   the BUS ATM  address is
        omitted at creation time then this object defaults to
        the  value of all  zeros  (none of the  busAtmAddrSpec
        value   is  relevant).  If the    BUS  ATM address  is
        specified  at creation time   but this object omitted,
        then this object  defaults  to the  value of all  ones
        (all of the busAtmAddrSpec is relevant)."
    ::= { busEntry 4 }

busAtmAddrActl OBJECT-TYPE
    SYNTAX AtmLaneAddress
--    Rsyntax OCTET STRING(SIZE(0..20))
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        " The  resultant ATM address in use  by the BUS.  This
        object is a product of the specified ATM address, mask
        and interaction with the switch via the ILMI."
    ::= { busEntry 5 }

busIfIndex OBJECT-TYPE
    SYNTAX Integer32
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        "  The interface that a BUS will forward traffic over.
                      The value specified for this object must equate to a
                      value of ifIndex in the ifTable.  The interface  will
                      be for that particular ATM port (the physical
                      interface, not a logical layer on top of it). This
                      object can only be specified upon row creation and
                      cannot be altered there after."
    ::= { busEntry 6 }

busSubIfNum OBJECT-TYPE
    SYNTAX Integer32
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        " Specifies   the  sub-interface number that  the  BUS
        will reside on.  This sub-interface may be shared with
        a LEC or BUS of the same ELAN  but is not required to
        do  so.  If no value  is  specified for this object at
        row creation time, then a sub-interface will be chosen
        by  the agent. This   object may only be  specified at
        row creation time and cannot be altered thereafter."
    ::= { busEntry 7 }

busUpTime OBJECT-TYPE
    SYNTAX TimeStamp
--    Rsyntax TimeTicks
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        " The  value    of sysUpTime  when  this  BUS   became
        enabled."
    ::= { busEntry 8 }

busLanType OBJECT-TYPE
    SYNTAX INTEGER {
        dot3(1),
        dot5(2)
        }
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        " The type of legacy LAN that this LES emulates."
    DEFVAL { dot3 }
    ::= { busEntry 9 }

busMaxFrm OBJECT-TYPE
    SYNTAX INTEGER {
        dot3(1516),
        tr4Mb(4544),
        rfc1626(9234),
        tr16Mb(18190)
        }
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        "  The maximum  frame size  that  the emulated LAN may
        accept."
    DEFVAL { dot3 }
    ::= { busEntry 10 }

busMaxFrmAge OBJECT-TYPE
    SYNTAX INTEGER(1..4)
--  Units
--    seconds
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        " The maximum number of seconds a BUS will hold onto a
        packet for forwarding until it is dropped.  Dropping a
        packet  will   result  in  the   incrementing   of the
        busFrmTimeOuts counter."
    DEFVAL { 1 }
    ::= { busEntry 11 }

busOutFwdOctets OBJECT-TYPE
    SYNTAX Counter32
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "  The number of  octets that  this  BUS has forwarded
        since its initialization."
    ::= { busEntry 12 }

busOutFwdUcastFrms OBJECT-TYPE
    SYNTAX Counter32
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        " The number  of  frames that  the BUS  has  forwarded
        which were  unicast data frames  including all control
        frames (i.e. they were flooded from the client)."
    ::= { busEntry 13 }

busOutFwdNUcastFrms OBJECT-TYPE
    SYNTAX Counter32
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "  The number of  frames  that  the BUS has  forwarded
        which were multicast frames."
    ::= { busEntry 14 }

busFrmTimeOuts OBJECT-TYPE
    SYNTAX Counter32
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        " The number of frames dropped by  the BUS due to time
        out."
    ::= { busEntry 15 }

busMultiFwdVpi OBJECT-TYPE
    SYNTAX CiscoVpiInteger
--    Rsyntax INTEGER(-1..255)
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        " The   virtual  path  identifier for    the multicast
        forward VCC. "
    ::= { busEntry 16 }

busMultiFwdVci OBJECT-TYPE
    SYNTAX CiscoVciInteger
--    Rsyntax INTEGER(-1..65535)
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "   The virtual channel   identifier for the multicast
        forward VCC."
    ::= { busEntry 17 }

busOperStatus OBJECT-TYPE
    SYNTAX INTEGER {
        active(1),
        inactive(2)
        }
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "  This object  reflects the actual   state of the BUS
        which may  differ  from  that  of  the  busAdminStatus
        object.    This  can   occur     when  the   interface
        ifOperStatus is  'down'     but    the   corresponding
        busAdminStatus is 'active'."
    ::= { busEntry 18 }

busAdminStatus OBJECT-TYPE
    SYNTAX INTEGER {
        active(1),
        inactive(2)
        }
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        "    The desired   state  of  the   designated BUS  as
        prescribed by the operator.  The  actions of the agent
        will,  if at  all possible,  eventually  result in the
        desired state being  reflected in  the busOperStatus."
    DEFVAL { active }
    ::= { busEntry 19 }

busStatus OBJECT-TYPE
    SYNTAX RowStatus
--    Rsyntax INTEGER {
--        active(1),
--        notInService(2),
--        notReady(3),
--        createAndGo(4),
--        createAndWait(5),
--        destroy(6)
--        }
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        " The status of the BUS  entry.  This object cannot be
        set  to active until   the  busIfIndex object  has  an
        appropiate  value.   Note  that implementations   that
        do    not  support  separate     LES/BUS entities  may
        refuse row  creation in  this table.  Creation  of
        BUS entities  for those implementation  is facilitated
        in the LES MIB."
    ::= { busEntry 20 }

busClientTable OBJECT-TYPE
    SYNTAX SEQUENCE OF BusClientEntry
    ACCESS not-accessible
    STATUS mandatory
    DESCRIPTION
        " A (conceptual) table listing the clients associated
        with a BUS.  Note that the local or network management
        will not create or destroy rows in this table but
        may only inspect what LECs are currently joined
        with the BUS."
    ::= { ciscoBusMIBObjects 2 }

busClientEntry OBJECT-TYPE
    SYNTAX BusClientEntry
    ACCESS not-accessible
    STATUS mandatory
    DESCRIPTION
        " An entry (conceptual) row that denotes a client that
        is establishing/has established a multicast send VC to
                      the BUS."
    INDEX { busElanName, busIndex, busClientId }
    ::= { busClientTable 1 }

BusClientEntry ::= SEQUENCE {
    busClientId INTEGER,
    busClientIfIndex Integer32,
    busClientMSendVpi CiscoVpiInteger,
    busClientMSendVci CiscoVciInteger,
    busClientAtmAddress AtmLaneAddress
    }

busClientId OBJECT-TYPE
    SYNTAX INTEGER
    ACCESS not-accessible
    STATUS mandatory
    DESCRIPTION
        " A unique identifier for a LEC which is establishing/
        has-established a multicast send VC to the BUS.  The
        identifier only persists for as long as the LEC is
        associated with this particular BUS.  If the LEC is
        dropped and rejoins the ELAN then a new identifier may
        be attributed to it."
    ::= { busClientEntry 1 }

busClientIfIndex OBJECT-TYPE
    SYNTAX Integer32
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        " The interface of the uni-directional multicast send
                      connection between the LEC and BUS."
    ::= { busClientEntry 2 }

busClientMSendVpi OBJECT-TYPE
    SYNTAX CiscoVpiInteger
--    Rsyntax INTEGER(-1..255)
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        " The VPI of the uni-directional multicast send
                      connection between the LEC and BUS."
    ::= { busClientEntry 3 }

busClientMSendVci OBJECT-TYPE
    SYNTAX CiscoVciInteger
--    Rsyntax INTEGER(-1..65535)
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        " The VCI of the uni-directional multicast send
                      connection between the LEC and BUS."
    ::= { busClientEntry 4 }

busClientAtmAddress OBJECT-TYPE
    SYNTAX AtmLaneAddress
--    Rsyntax OCTET STRING(SIZE(0 | 20))
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        " The address associated with the LANE client on the 
        mulicast send VCC."
    ::= { busClientEntry 5 }

ciscoBusGroup OBJECT IDENTIFIER ::= { ciscoBusMIBGroups 1 }
-- OBJECT-GROUP
--  Status
--    mandatory
--  Descr
--     A collection of objects for the managing of BUS operation.
--  objects
--    busAtmAddrSpec, busAtmAddrMask, busAtmAddrActl, busIfIndex, 
--    busUpTime, busLanType, busMaxFrm, busMaxFrmAge, 
--    busOutFwdOctets, busOutFwdUcastFrms, busOutFwdNUcastFrms, 
--    busFrmTimeOuts, busMultiFwdVpi, busMultiFwdVci, busOperStatus, 
--    busAdminStatus, busStatus

ciscoBusSubIfGroup OBJECT IDENTIFIER ::= { ciscoBusMIBGroups 2 }
-- OBJECT-GROUP
--  Status
--    mandatory
--  Descr
--     For those implementations that wish to tie their LE service
--                  components to an aflane_802x ifIndex.
--  objects
--    busSubIfNum

ciscoBusClientGroup OBJECT IDENTIFIER ::= { ciscoBusMIBGroups 3 }
-- OBJECT-GROUP
--  Status
--    mandatory
--  Descr
--     A collection of objects for the identification of a
--    BUS's multicast send VCs.
--  objects
--    busClientIfIndex, busClientMSendVpi, busClientMSendVci, 
--    busClientAtmAddress

ciscoBusMIBCompliance OBJECT IDENTIFIER ::= { ciscoBusMIBCompliances 1 }
-- MODULE-COMPLIANCE
--  Status
--    mandatory
--  Descr
--     The compliance statement for SNMP entities that support
--    Cisco's BUS MIB.
--  Module
--    >>current<<
--   MandGroup
--    ciscoBusGroup
--   OptGroup
--    ciscoBusSubIfGroup
--   ObjVar
--    busAtmAddrSpec
--   ObjVar
--    busAtmAddrMask
--   ObjVar
--    busIfIndex
--   ObjVar
--    busSubIfNum
--   ObjVar
--    busLanType
--   ObjVar
--    busMaxFrm
--   ObjVar
--    busAdminStatus


END