Prusa i3 Khalkeus.ini

bed_custom_model = 
bed_custom_texture = 
bed_shape = 0x0,215x0,215x185,0x185
before_layer_gcode = 
between_objects_gcode = 
cooling_tube_length = 5
cooling_tube_retraction = 91.5
default_filament_profile = ""
default_print_profile = 
deretract_speed = 0
end_gcode = ; -- END GCODE --\nM104 S0                            ;set extruder temperature to zero (turned off)\nG91                                      ;set to relative positioning\nG1 E-20 F300                 ;retract the filament a bit to release some of the pressure\nG1 Z10                                ;move extruder up 10 mm\nG90                                     ;set to absolute positioning\nG1 X0 Y180 F1200       ;expose the platform\nM84                                    ;turn off steppers\n; -- end of END GCODE --
extra_loading_move = -2
extruder_colour = ""
extruder_offset = 0x0
gcode_flavor = marlin
high_current_on_filament_swap = 0
host_type = octoprint
inherits = 
layer_gcode = 
machine_max_acceleration_e = 10000,10000
machine_max_acceleration_extruding = 650,650
machine_max_acceleration_retracting = 1000,1000
machine_max_acceleration_x = 1100,1100
machine_max_acceleration_y = 1100,1100
machine_max_acceleration_z = 100,100
machine_max_feedrate_e = 25,25
machine_max_feedrate_x = 200,200
machine_max_feedrate_y = 200,200
machine_max_feedrate_z = 3.3,3.3
machine_max_jerk_e = 5,5
machine_max_jerk_x = 10,10
machine_max_jerk_y = 10,10
machine_max_jerk_z = 0.4,0.4
machine_min_extruding_rate = 0,0
machine_min_travel_rate = 0,0
max_layer_height = 0.3
max_print_height = 175
min_layer_height = 0.06
nozzle_diameter = 0.4
parking_pos_retraction = 92
print_host = 
printer_model = 
printer_notes = PRINTER_VENDOR_GKR\nPRINTER_MODEL_KHALKEUS
printer_settings_id = 
printer_technology = FFF
printer_variant = 
printer_vendor = 
printhost_apikey = 
printhost_cafile = 
remaining_times = 0
retract_before_travel = 2
retract_before_wipe = 0%
retract_layer_change = 0
retract_length = 2
retract_length_toolchange = 10
retract_lift = 0
retract_lift_above = 0
retract_lift_below = 0
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 40
serial_port = 
serial_speed = 250000
silent_mode = 0
single_extruder_multi_material = 0
start_gcode = ; -- START GCODE --\nG21                                ;set units to millimetres\nG90                               ;set to absolute positioning\nM106 S0                      ;set fan speed to zero (turned off)\nG28 X0 Y0                  ;move to the X/Y origin (Home)\nG28 Z0                         ;move to the Z origin (Home)\nM420 S1                       ;enable mesh leveling\nG1 Z15.0 F1200        ;move Z to position 15.0 mm\nG92 E0                         ;zero the extruded length\nG1 E20 F200              ;extrude 20mm of feed stock\nG92 E0                         ;zero the extruded length again\nG1 F7200                    ;set feedrate to 120 mm/s\n; -- end of START GCODE --
thumbnails = 
toolchange_gcode = 
use_firmware_retraction = 0
use_relative_e_distances = 0
use_volumetric_e = 0
variable_layer_height = 1
wipe = 0
z_offset = 0